Votes - 3, Average rating: 3
(
)
)
|
manual abstract
C (Pulse button will not light up.) D G. Power Button (On/Off button) F – Turns the product On and Off. H. Stop Button – Use to Stop the product. (Stop button will not light up.) G H 345687 5 Using Your Product Before you use the product for the first time, separate the Jar Lid, Filler Cap and Blade from the jar. Wash in warm, soapy water or use the top rack in the dishwasher for smaller parts. Blender jar is safe for bottom rack cleaning. Rinse and dry well. Assembly 1. Install the Sealing Ring over the 6 Point Star Blade. Blade is sharp. Handle with care. 2. Turn the jar upside down so the small opening is at the top. 3. Turn the 6 Point Star Blade with Sealing Ring upside down and place into the bottom of the jar. 4. Position the open end of the Threaded Jar Bottom Cap over the jar and Sealing Ring. Turn clockwise to tighten. Be sure the Threaded Jar Bottom Cap is securely tightened onto the jar before using. 5. Slide the jar onto the base. 6. Plug the power cord into a standard household 120/127-volt, 60 hz. AC outlet. Using the Pre-Programmed Settings 1. Press the ON/OFF power button to turn the product on. The power light will blink, meaning the product is active and ready to use. 2. Choose a recipe from the recipe section of this manual or use one of your own. 3. Put the ingredients into the jar. 4. Secure the Filler Cap and Jar Lid. 5. Press one of the two Pre-Programmed Setting buttons appropriate for your recipe (“Frozen Drinks” or “Food Chop”.) 6. To change your selection, press Stop followed by another Pre-Programmed Setting button (“Frozen Drinks” or “Food Chop”.) 7. Once the program is finished, the product automatically stops. Please note: You may press the “Stop” button to cancel the program at any time. The blinking red light indicates that the blender is ready. 8. Press the ON/OFF power button to turn the product off. This product is pre-programmed to turn off automatically if not used for a period of several minutes. All lights will turn off when the unit automatically powers down. 6 Using the Manual Controls Use these buttons for personal recipes or to continue mixing after a Pre-Programmed Setting is finished. 1. Press the ON/OFF power button to turn the product on. The power light will blink, meaning the product is active and ready to use. 2. Choose a recipe from the recipe section of this manual or use one of your own. 3. Put the ingredients into the jar. 4. Secure the Jar Lid with Filler Cap onto the Blender Jar. 5. Press the manual control button of your choice based on your recipe or blending needs. 6. Press the “Stop” button to cancel the operation at any time. 7. Press the ON/OFF power button to turn the product off. Caring for Your Product Cleaning Unplug the blender. Release the 6 Point Star Blade from the Threaded Jar Bottom Cap by turning the Cap counterclockwise. ALWAYS USE CAUTION WHEN REMOVING THE BLADE ASSEMBLY. Use the top rack of the dishwasher for the Jar Lid, Filler Cap and 6 Point Star Blade. Place Sealing Ring into bottom basket of dishwasher and the Blender Jar in the bottom rack. You can also wash the parts in warm, soapy water. Rinse well and dry. Wipe the base with a soft, damp cloth to clean. Never submerge the blender base in any liquids. Check the parts as you put them back together. Storing Reassemble the blender for storage. Leave the lid open slightly so no odors are retained. WARNING: Never put the jar, or any other parts, in a microwave oven. Never store foods or drinks in the jar. Servicing Call our toll-fee, automated phone line to find the Service Center nearest to you. If repairs are needed, send your appliance only to an authorized Oster® Appliance Service Center. Use only replacement parts from Jarden Consumer Solutions. See How to Obtain Warranty Service on page 15. 7 Blending Tips Liquids Put liquids into the jar first, unless the recipe says otherwise. Using the Jar Lid Filler Cap Opening Do not remove the lid while in use. Food may splatter if you do. Instead, open the Filler Cap to add smaller ingredients. Working with Hot Foods or Liquids WARNING: When you work with HOT FOODS, remove the Filler Cap to vent steam. Keep hands and other exposed skin away from the lid opening to prevent possible burns. When you work with HOT LIQUIDS, remove the Filler Cap and start at a low speed, and then gradually increase to a faster speed. Do not add liquid over the 4 cup (1L) level. Always keep hands away from steam. Ingredients Quantities Use only the amount of food suggested in the recipes. If you want greater amounts, prepare in batches. Using larger amounts may overload and strain the motor. You might also get different results from those described. Recipes These recipes have been optimized for the Pre-Programmed Settings. When experimenting with your own recipes you may choose to stop the Pre-Programmed Setting at any time by hitting the Stop button or you may run the cycle more than once if a different consistency is desired. Frozen Drinks: Frozen Marg...