Votes - 4, Average rating: 4.3
(
)
)
|
manual abstract
15. To reduce the risk of injury, never place cutting blades on base without jar properly attached. 16. Always operate blender with cover in place. 17. When blending hot liquids, remove center piece of two-piece cover. Do not fill blender container beyond the 3 cup level. Always begin processing at the lowest speed setting. Keep hands and other exposed skin away from the cover opening to prevent possible burns. 18. Screw on jar retaining ring firmly. Injury can result if moving blades accidentally become exposed. 19. If the jar should turn when the motor is switched ON, switch OFF immediately and tighten jar in threaded retaining ring. 20. Do not leave blender unattended while it is operating. 21. To disconnect cord, turn the control to OFF, then remove plug from wall outlet. 22. Do not use appliance for other than intended purpose. SAVE THESE INSTRUCTIONS 3 840144900 ENv02.qxd 1/4/06 4:36 PM Page 4 OTHER CONSUMER SAFETY INFORMATION This appliance is intended for household Use for food or liquids only. The length of the cord used on this appliance was selected to reduce the hazards of becoming tangled in, or tripping over a longer If a longer cord is necessary an approved extension cord may be used. The electrical rating of the extension cord must be equal to or greater than the rating of the blender. Care must be taken to arrange the extension cord so that it will not drape over the countertop or tabletop where it can be pulled on by children or accidentally tripped over. If the cutting blades lock and do not move, it will damage the motor. Do not use. Call the toll-free customer service number for information. Do not place blender jar in the freezer filled with food or liquid. This will freeze and damage the cutting blades, jar, and motor. 4 Parts and Features 1. Filler- Cap 2. Lid 3. Jar PULSE Button – For instant control the Pulse operates only as long as the button is held down. The blender motor stops when the button is released. 4. Cutting Blades 5. Jar Nut 6. Base 7. Control Panel NOTE: Rubber gasket is permanently affixed to the blades. Do not try to remove it. 5 840144900 ENv02.qxd 1/4/06 4:36 PM Page 6 Before First Use After unpacking the blender, wash everything except the blender base in hot, soapy water. Dry thoroughly. Do not place in dishwasher. Wipe the blender base with a damp cloth sponge. DO NOT IMMERSE THE BASE IN Care should be taken when handling the blades as very sharp. How to Assemble and Use IMPORTANT: Your blender jar and cutting blades are subject to wear during normal use. Always inspect jar for nicks, chips or cracks. Always inspect cutting blades for broken, cracked or loose blades. If jar or cutting blades are damaged, do not use. Contact an authorized service facility to obtain replacement parts. 1. Make sure blender is unplugged. Place blender base on clean, dry surface to keep foreign particles from being pulled up into motor during operation. 2. Place blades in jar nut. Screw jar onto the jar nut with cutting blades. 3. Make sure the jar nut is firmly screwed onto the jar. If not, it may loosen later when motor is turned on. 4. Set jar into place on blender base, making sure it is securely seated. If not, gently rock the jar until seated. 5. Plug cord into outlet. 6. Put ingredients in jar, place lid on jar. 6 7. Process food or beverages. Place blending liquids. Push button on panel to start blender. 8. ALWAYS turn blender off and wait until blades have stopped rotating before removing jar. 9. To remove jar after blending is complete, lift the straight up. If it is not easily removed, rock gently and lift. Do not twist. 10. NEVER replace jar onto unit while motor is running. How to Clean the Blender 1. Unplug blender from electrical outlet. 2. Wipe blender base, control panel, and cord with a damp cloth or sponge. To remove stubborn spots, use a mild, non-abrasive cleanser. 3. To clean jar, unscrew jar nut and remove cutting blades from jar. 4. Carefully remove cutting blades from jar nut. 5. Carefully wash blades, jar nut, jar (if plastic), and cover in hot, soapy water. Rinse and dry thoroughly. Do not soak. Do not wash blades, jar nut, plastic jar, or cover in a dishwasher. 6. Reassemble cutting blades onto jar, replace jar onto blender base. 7. Store blender with cover ajar to prevent container odor. 7 840144900 ENv02.qxd 1/4/06 4:36 PM Page 8 General Tips • For best blending performance, the recommended per recipe is one cup (8 oz./250 ml). Add more liquid if food is not blending properly. • Processing hot foods or liquids in the blender hot liquid to spurt out when the cover is removed. Always remove the filler-cap from the cover before blending hot foods or liquids. • To add foods when blender is operating, remove filler-cap from container cover and add ingredients through the opening. • If blending action stops during blending or ingredients stick to sides of the jar, turn blender OFF. Remove cover and use a rubber spatula to push mixture toward blades. • Do not...