Votes - 2, Average rating: 4
(
)
)
|
manual abstract
AC ChargerREGISTER YOUR PRODUCT ONLINE FEATURES FEATURES 54 CS55CS50Front: Rear: Listening Volume/Mute Talk Indicator LightSpeakerBattery CoverCall Control ButtonMicrophoneHandset Lifter ArmRinger Microphone Jack (remove cover) Height SwitchAccessory JackPower CordHeadsetHandset LifterTelephone Cord JackTelephone Handset JackSpeaking Volume Major AdjustAC Charging JackHandset Lifter JackBase - Top ViewBase - Bottom ViewCharging CradleFront: Rear: Indicator LightsTalking (Green) Power (Red) Charging (Amber) Listening VolumeMajor AdjustTelephone CordTelephone Configuration DialIntelliStand™ On/Off Switch(to automate callcontrol button) Speaking VolumeMinor Adjust Rear: Listening Volume/Mute Talk Indicator LightSpeakerBattery CoverCall Control ButtonMicrophoneHandset Lifter ArmRinger Microphone Jack (remove cover) Height SwitchAccessory JackPower CordHeadsetHandset LifterTelephone Cord JackTelephone Handset JackSpeaking Volume Major AdjustAC Charging JackHandset Lifter JackBase ViewBase - Bottom ViewCharging SETUP SETUP 1234 Unplug the handset cord from phone.Plug the phone cord that is connected to the CS50/CS55 base into the handset jack on the phone. CAUTION: Your phone may have two similar jacks. Put the cord only in the jack from which the handset came. 1234 Plug the AC charger into an outlet and into the base’s AC charging jack. See step 4A for detailed location. Plug the handset cord into the handset Plug the AC charger into the base’s AC jack in the base. Push in until it clicks. charging jack. Push in firmly. Plug the handset cord into the handset jack in the bottom of the base. See step 3A for detailed location. NOTE: The access to the handset jack is fairly small. If you have large hands you may want to ask someone with smaller fingers to do this step. 76 21ADBC 1. Plug handset lifter power cord into handset lifter jack on base. Push firmly into base. 2. Position handset lifter under the handset on your phone. Verify that the lifter is located on top of the telephone speaker. If not, you will need to attach the ringer microphone as described on page 22. NOTE: Remove only a tiny piece of mounting tape backing to temporarily stick lifter into position; you may need to move it later. 3IntelliStand™ offIntelliStandon Set the IntelliStand switch to Intellistand off ( ) if you 31234IntelliStandoffIntelliStandonwant to control the handset lifter with the call control button on your headset. Set the Intellistand switch to Intellistand on ( ) if you 31234IntelliStandoffIntelliStandonwant the handset to automatically pick up when you take the headset off the charging cradle. SETUP - HANDSET LIFTER (Optional) • 20 minutes = minimum charge to continue setup • 3 hours = full charge 1. Slide headset into charging cradle. 2. Gently press down on the headset to ensure that headset is in correct position. Amber charge indicator light on base will flash while charging and will change to solid amber when fully charged. CHARGING POSITIONING 6” 12” The minimum recommended separation distance is shown above. IMPORTANT: Incorrect positioning can cause noise and interference problems. 98 ADJUSTINGFIT Wearing OptionsRetaining Ring Snap speaker into retaining ring of desired wearing option (headband or earloop). 112 1. Adjust headband to fit. 2.Rotate headset in retaining ring until microphone is pointing toward your chin. MAKING/ANSWERING/ENDINGCALLS Without Handset lifter 122 To make a call: 1. Take your handset off-hook. Dial tone should sound through handset (if not, check compatibility — see page 13). 2. Press the call control button on the headset. The talk indicator lights on both the base and the headset should go on, indicating a successful link. Dial tone should sound through headset. Dial using the telephone keypad. To answer a call: 1. Take the handset off-hook. 2. Press the call control button on the headset to answer a call. To end a call: Press the call control button on the headset, then hang up the handset. NOTE: If either you or the recipient have trouble hearing, please check compatibility (page 13). 1110 MAKING/ANSWERING/ENDING CALLS 2With Handset Lifter (Optional) 12212 To first test proper set up of the handset lifter: 1. Press the call control button on headset to activate handset lifter and lift handset from phone. Dial tone should sound in headset if the handset is raised high enough. 2. If no dial tone, adjust lifter height switch or reposition lifter under handset. If you still do not hear a dial tone, you may need to insert extender arm (see page 22) or check compatibility (page 13). After verifying dial tone, use mounting tape to secure handset lifter in position. 2With Handset Lifter (Optional) 12212 To make/answer a call: 1. Press the call control button to raise the handset lifter. 2. Use the telephone keypad to dial the number. To end a call: Press the call control button to lower the handset lifter. (Phone will hang up.) NOTE: If either you or the recipient have trouble hearing, please check...