Votes - 5, Average rating: 4
(
)
)
|
manual abstract
The Bluetooth® word mark and logos are owned by the Bluetooth SIG, Inc. and any use of such marks by Cardo Systems, Inc. is under license. Other trademarks and trade names are those of their respective owners. English 3 scala rider® Q2™ MultiSet INTRODUCTION Congratulations and thank you for choosing the scala rider Q2 MultiSet Bluetooth® Headset package for bikers. This User Guide will help you operate the headset, but you should first familiarize yourself with the Bluetooth functionality of your cellular phone and/or GPS device before using the scala rider Q2. This retail box contains two scala rider Q2 headsets that already factory paired (see details below). In wide open terrain two bikers can communicate via intercom (in full duplex*) at a range of up to 500 m / 1,640 ft., subject to terrain and external conditions. The scala rider Q2 is multi-talented and (in addition to its connection to the second Q2 unit) it can also serve as a stand-alone unit for the following connectivity modes: • As a Bluetooth headset for mobile phone communication** • As a Biker-to-Passenger Intercom device that connects with any scala rider headset worn by the passenger • As a speaker that transmits GPS Navigation instructions from a compatible GPS device*** • As a speaker that transmits audio from the embedded FM Radio • As a speaker that transmits music from your MP3 player NOTE: Each Q2 headset can establish an audio connection with one Bluetooth device at a time. Read the section “Using the Headset” on how to switch the audio connection between the paired devices. ____________________ * Full duplex calls allow you to speak and hear the other party speak simultaneously ** Mobile phones that do not support the Bluetooth Handsfree profile may prevent you from using the Redial and Call Reject features. The Q2 supports headset and handsfree profiles at up to 10 m / 30 ft. distance from the mobile phone *** Requires Bluetooth compatibility on the part of the GPS device CONTENTS OF RETAIL BOX Two Headsets Volume Up Charging Jack Volume Down CTRL – Control Button • Power On, Power Off • Answer/End Call MC – Multi-Connection • Radio On/Off/change stations • Initiate/Terminate Buddy Intercom call with Primary or Secondary Buddy Two Helmet Clamps Left Speaker (short cord) Right Speaker (long cord) Microphone Back Plate Tab Sliding Plate MP3 Jack NOTE: The scala rider Q2 is also available in a cord-mounted microphone version to better fit certain full-faced helmets with tight chin sections. 2 Wall Chargers 2 Allen Wrenches 2 sets of Velcro Pads 2 MP3 Cables 2 MP3 Cable Holders 2 Glue Plates 2 Pre-moistened Towelettes 2 Carry-Pouches 4 Microphone Sponges Flat sponge for full-face helmets and round sponge for other helmet types User Guide, including Warranty and Registration form IMPORTANT: Your headsets are water-resistant, designed for use under moderate rain or snow conditions. However, the headsets are not waterproof and should not be used under severe weather conditions. The cover tongue protecting the Charging Jack should be kept tightly closed at all times to prevent moisture from entering the device. NOTE: WHILE MOST INSTRUCTIONS IN THIS MANUAL REFER TO THE HEADSET IN THE SINGULAR, THEY APPLY TO BOTH UNITS UNLESS INDICATED OTHERWISE. BEFORE USING (CHARGING THE HEADSET) Make sure that the headset is fully charged for at least five hours before initial use. 1. Connect the wall charger to the headset’s Charging Jack (located between the two Volume Buttons). 2. While charging, the Red Light turns on (it may take up to 15 seconds until the Red Light turns on). When charging is complete, the Red Light will turn off. SET UP AND CONFIGURATION STEP 1 SET UP FOR BIKE-TO-BIKE INTERCOM: PAIRING Pairing is a one time process that is required for mutual recognition between a headset and other Bluetooth devices. Once the two headsets are paired, they will remain paired and automatically recognize each other whenever they are within range. The two headsets in your retail box are already factory paired and relate to each other as the Primary Buddy connection. In addition, each unit can be paired with an additional scala rider headset for Intercom communication. Please note that you can speak via Intercom to one Buddy headset at a time. NOTE: This Manual refers to the Intercom users and other parties as: Primary Buddy and Secondary Buddy. GPS Built-in FM radio MP3 player Mobile phone Driver-to- Passenger Full-duplex Intercom Connection Bike-to-Bike Intercom up to 500 m / 540 yd )in open terrain( scala rider Q2 or other scala rider headset 4 scala rider® Q2™ MultiSet PRIMARY BUDDY PAIRING (two scala rider Q2 headsets) Your two MultiSet units are already factory paired and ready for use. If for any reason, you have to pair them again, proceed as follows: 1. If either headset is turned OFF, turn it ON by pressing and holding the CTRL Button until the Blue Light flashes three times. 2. Make sure that both headsets are now flashing slowly in Blue. 3...