WHEN ORDERING PARTS 16” Gas Chain Saw MODEL NO. TB3516NT / 41AZ356P766 DATE REVISED DATE PAGE 7/29/2004 N/A 1/2 TROV-BiLT SERVICE SPARE PARTS LIST SPECIFY MODEL NO. WHEN ORDERING PARTS DATE REVISED DATE 16” Electric Chain Saw 7/29/2004 MODEL NO. TB3516NT / 41AZ356P766 N/A No. STK CODE Parts No. Description Q No. STK CODE Parts No. Description Q 1 MC-6228-211403 HOUSING (R) 1 36 MC-6024-211507 SPRING 1 2 MC-6228-211504 CHAIN COVER ASS'Y 1 37 MC-6Q

WARNING: Never turn saw upside down to undercut. The saw cannot be controlled in this position. SecondcutFirstcutonpressuresideoflog Second cut First cut on pressure side of log BUCKING WITHOUT A SUPPORT S Overcut through 1/3 of the diameter of the log. S Roll the log over and finish with a second overcut. S Give special attention to logs under strain to prevent the saw from pinching. Make the first cut on the pressure side to relieve the stress on the log. BUCKING USING A LOG OR SUPPORT STAND S

After each use, ensure ON/STOP switch is in the STOP position, then clean all sawdust from the guide bar and sprocket hole. To maintain guide bar: S Move ON/STOP switch to the STOP posi tion. S Loosen and remove chain brake nuts and chain brake. Remove bar and chain from saw. S Clean the oil holes and bar groove after each 5 hours of operation. RemoveSawdustFromGuideBarGrooveOilHole SBurringofguidebarrailsisanormalprocessofrailwear.Removetheseburrswithaflatfile. SWhenrailtopisuneven,useaflatfile

A 40:1 ratio is obtained by mixing 0,125 liter of oil with 5 liters of unleaded gasoline. DO NOT USE automotive or boat oil. These oils will cause engine damage. When mixing fuel follow the instructions printed on the container. Always read and follow the safety rules relating to fuel before fueling your unit. IMPORTANT Experience indicates that alcohol blended fuels (called gasohol or using ethanol or methanol) can attract moisture which leads 8 to separation and formation of acids during stora

Reduced- --kickbackguidebars and low- --kickback saw chains reduce the chance and magnitude of kickback and are recommended. Your saw has a low kickback chain and bar as original equipment. Repairs on a chain brake should be made by an authorized servicing dealer. Take your unit to the place of purchase if purchased from a servicing dealer, or to the nearest authorized master service dealer. 5 S Tip contact in some cases may cause a lightning fast reverse REACTION, kicking the guide bar up and b

Veuilleznepasretournerleproduitaudetaillant. 1--800--554--6723ENGLISHPleasedonotreturnproducttoretailer. Porfavor,nodevuelvaelproductoallugardecompra. Veuilleznepasretournerleproduitaudetaillant. 1--800--554--6723 Register your product online at: Registre su producto en linea en: Enregistrez votre produit en ligne a l’adresse : Instruction Manual Manual de Instrucciones Manueld’InstructionsESPANOL For Occasional Use Only WARNING: Read and follow all Safety Rules andOperating Instructionsbefore u

HANDLE FUEL WITH CAUTION S Do not smoke while handling fuel or while operating the saw. S Eliminate all sources of sparks or flame in the areas where fuel is mixed or poured. There should be no smoking, open flames, or work that could cause sparks. Allow engine to cool before refueling. S Always have fire extinguishing tools available if you should need them. S Mix and pour fuel in an outdoor area on bare ground; store fuel in a cool, dry, well ventilated place; and use an approved, marked conta

Check immediately. Excessive vibranot repair a damaged cable, replace it with a tion can cause injury. new one. Use only Electrolux Outdoor -before passing to another person. Products replacement cable. Maintenance and storage 12. Always wind cable carefully, avoiding kink- 1. Keep all nuts, bolts and screws secure to be ing. sure the Hedgetrimmer is in safe working 13. Use only on AC mains supply voltage shown condition. on the product rating label. 2. Replace worn or damaged parts for safety.