Votes - 1, Average rating: 3 ( )

Manafacture: Homelite File size: 1.06 mb File name: 427ee5d8-ab09-4f3a-89fc-c3796f58b09b.pdf Language of manual:

OPERATING INSTRUCTIONS OPERATING INSTRUCTIONS Fig. 15 LIMBING Limbing a tree is the process of removing the branches from a fallen tree. Do not remove supporting limbs (A) until after the log is bucked (cut) into lengths (Fig. 16). Branches under tension should be cut from the bottom up to avoid binding the chain saw. A Fig. 16 Never cut tree limbs WARNING: while standing on a tree trunk. BUCKING Bucking is cutting a fallen log into lengths. Make sure you have a good footing and stand uphill of the log when cutting on sloping ground. If possible, the log should be supported so that the end to be cut off is not resting on the ground. If the log is supported at both ends and you must cut in the middle, make a downward cut halfway through the log and then make the undercut. This will prevent the log from pinching the bar and chain. Be careful that the chain does not cut into the ground when bucking as this causes rapid dulling of the chain. Fig. 17 When bucking on a slope, always stand on the uphill side. 1. Log supported along entire length: Cut from top (overbuck), being careful to avoid cutting into the ground (Fig. 17). 2. Log supported on 1 end: First, cut from bottom (underbuck) 1/3 diameter of log to avoid splintering. Second, cut from above (overbuck) to meet first cut and avoid pinching (Fig. 18). 3. Log supported on both ends: First, overbuck 1/3 diameter of log to avoid splintering. Second, underbuck to meet first cut and avoid pinching (Fig. 19). NOTE: The best way to hold a log while bucking is to use a sawhorse. When this is not possible, the log should be raised and supported by the limb stumps or by using supporting logs. Be sure the log being cut is securely supported. Fig. 18 Fig. 19 BUCKING USING A SAWHORSE For personal safety and ease of cutting, the correct position for vertical bucking is essential (Fig. 20). A. Hold the saw firmly with both hands and keep thesaw to the right of your body while cutting. B. Keep the left arm as straight as possible. C. Keep weight on both feet. Fig. 20 A B C While the saw is cutting, be sure the chain and bar are being properly lubricated. CAUTION: MAINTENANCE AND REPAIR INSTRUCTIONS MAINTENANCE AND REPAIR INSTRUCTIONS MAINTENANCE SCHEDULE Perform these required maintenance procedures at the frequency stated in the table. These procedures should also be a part of any seasonal tune-up. NOTE: Some maintenance procedures may require special tools or skills. If you are unsure about these procedures take your unit to any non-road engine repair establishment, individual or authorized service dealer. NOTE: Maintenance, replacement, or repair of the emission control devices and system may be performed by any non-road engine repair establishment, individual or authorized service dealer. To prevent serious WARNING: injury, never perform maintenance or repairs with unit running. Always service and repair a cool unit. Disconnect the spark plug wire to ensure that the unit cannot start. A good preventive maintenance program of regular inspection and care will increase life and improve performance of your chain saw. This maintenance checklist is a guide for such a program. Cleaning, adjustment, and part replacement may be required, under certain conditions, at more frequent intervals than those indicated. MAINTENANCE CHECKLIST LISTES DES VERIFICATIONS D’ENTRETIEN LISTA DE VERIFICACION DEL MANTENIMIENTO EACH USE CHAQUE USAGE CADA USO HOURS OF OPERATION HEURES D’OPERATION HORAS DE OPERACION ITEM / PIECE / PARTE ACTION / ACTION / ACCION 10 20 SCREWS / NUTS / BOLTS VIS / ECROUS / BOULONS TORNILLOS / TUERCAS / PERNOS INSPECT / TIGHTEN INSPECTER / RESSERRER INSPECCIONAR / APRETAR 4 AIR FILTER FILTRE A AIR FILTRO DE AIRE CLEAN OR REPLACE NETTOYER OU REMPLACER LIMPIAR O REEMPLAZAR 4 FUEL FILTER / OIL FILTER FILTRE ESSENCE / FILTRE A HUILE FILTRO DEL COMBUSTIBLE / FILTRO DE ACEITE REPLACE REMPLACER REEMPLAZAR 4 SPARK PLUG BOUGIE BUJIA DE ENCENDIDO CLEAN / ADJUST / REPLACE NETTOYER / REGLER / REMPLACER LIMPIAR / AJUSTAR / REEMPLAZAR 4 SPARK ARRESTER SCREEN ECRAN PARE-ETINCELLES PANTALLA DEL PARACHISPAS INSPECT INSPECTER INSPECCIONAR 4 REPLACE AS REQUIRED REMPLACER SUIVANT LES BESOINS REEMPLAZAR SEGUN SE REQUIERA 4 FUEL HOSES DURITS D’ESSENCE MANGUERAS DE COMBUSTIBLE INSPECT INSPECTER INSPECCIONAR 4 *REPLACE AS REQUIRED *REMPLACER SUIVANT LES BESOINS *REEMPLAZAR SEGUN SE REQUIERA CHAIN BRAKE® COMPONENTS COMPOSANTS DE CHAIN BRAKE® COMPONENTES DEL CHAIN BRAKE® INSPECT INSPECTER INSPECCIONAR 4 *REPLACE AS REQUIRED *REMPLACER SUIVANT LES BESOINS *REEMPLAZAR SEGUN SE REQUIERA *Recommended for Maintenance by an Authorized Service Center Technician. *Il est recommande de confier ces operations a un technicien agree. *Recomendamos que el Centro de Servicio Autorizado proporcione el mantenimiento. MAINTENANCE AND REPAIR INSTRUCTIONS MAINTENANCE AND REPAIR INSTRUCTIONS INSTALL THE GUIDE BAR To ensure the bar and CAUTION: chain receive oil, ONLY USE THE ORIGINAL STYLE BAR with the oil passag...

Download now

Please, enter two numbers from picture: