Votes - 2, Average rating: 3 ( )

Manafacture: Remington File size: 1.33 mb File name: 391368d9-b224-405c-967c-99c8ba3baeb8.pdf Language of manual:

4. Make a test cut adjust the H needle for best cutting power, not for maximum speed. (1) L needle (2) H needle (3) Idle adjusting screw ¦ CHAIN BRAKE This machine is equipped with an automatic brake to stop saw chain rotation upon occurrence of kickback during saw cutting. The brake is automatically operated by inertial force, which acts on the weight fitted inside the front guard. This brake can also be operated manually with the front guard turned down to the guide bar. To release the brake, pull up the front guard toward the front handle till a “click” sound is heard. (1) Release (2) Activate (3) Front guard Be sure to confirm brake operation during daily inspection. How to confirm: 1) Turn off the engine. 2) Holding the chain saw horizontally, release your hand from the front handle, hit the tip of the guide bar to a stump or a piece of wood, and confirm brake operation. Operating level varies by bar size. In case the brake is not effective, ask our dealer for inspection and repairs. If the engine keeps rotating at high speed with the brake engaged, the clutch will overheat causing trouble. IMPORTANT 7. Operation (1) (2)(3) F7-8 (1) (2) (3) F7-9 F7-10 .15 . IMPORTANT 7. Operation (1) (2)(3) F7-8 (1) (2) (3) F7-9 F7-10 .15 . 7. Operation When the brake engages during operation, immediately release the throttle lever to stop the engine. (1) F7-11 ¦ STOPPING THE ENGINE 1. Release the throttle lever to allow the engine to idle for a few minutes. 2. Set the switch to the “O” (STOP) position. (1) Switch ¦ CARBURETOR ANTI-FREEZE MECHANISM Operating chain saws in temperatures of 0 – 5°C at times of high humidity may result in ice forming within the carburetor, and this in turn may cause the output power of the engine to be reduced or for the engine to fail to operate smoothly. This product has accordingly been designed with a ventilation hatch on the right side of the surface of the insulator cover to allow warm air to be supplied to the engine and to thereby prevent icing from occurring. Under normal circumstances the product should be used in the normal operating mode, i.e., in the mode to which it is set at the time of shipment. However when the possibility exists that icing may occur, the unit should be set to operate in the antifreeze mode before use. Stop the engine, remove the cylinder cover and install the grommet A to the appropriate position of the mode. See ¦ Maintenance part for how to remove the cylinder cover. (1) Normal operation mode (2) Anti-freeze mode (3) Insulator (4) Carburetor (5) Grommet A (1) (5)(4) (3) (5) (2) F7-12 .16 . 8. Sawing WARNING F8-1 • Before proceeding to your job, read "For Safe Operation" section It is recommended to first practice sawing easy logs. This also helps you get accustomed to your unit. •Always follow the safety regulations. The chain saw must only be used for cutting wood. It is forbidden to cut other types of material. Vibrations and kickback vary with different materials and the requirements of the safety regulations would not be respected. Do not use the chain saw as a lever for lifting, moving or splitting objects. Do not lock it over fixed stands. It is forbidden to hitch tools or applications to the P.t.o. that are not specified by the manufacturer. •It is not necessary to force the saw into the cut. Apply only light pressure while running the engine at full throttle. • When the saw chain is caught in the cut, do not attempt to pull it out by force, but use a wedge or a lever to open the way. ¦ GUARD AGAINST KICKBACK (F8-1) • This saw is equipped with a chain brake that will stop the chain in the event of kickback if operating properly. You must check the chain brake operation before each usage by running the saw at full the throttle for I -2 seconds and pushing the front hand guard forward. The chain should stop immediately with the engine at full speed. If the chain is slow to stop or does not stop, replace the brake band and clutch drum before use. • It is extremely important that the chain brake be checked for proper operation before each use and that the chain be sharp in order to maintain the kickback safety level of this saw. Removal of the safety devices, inadequate maintenance, or incorrect replacement of the bar or chain may increase the risk ot serious personal injury due to kickback. .17 . F8-2 F8-3 F8-4 F8-5 F8-6 .19 . F9-2 (1) (2) (1) (2) A B F9-3 (3) 9. Maintenance 4. Remove the cleaner element by unfastening the hooks. Split the element into halves and wash in neutral detergent and warm water. After cleaning, dry the element completely. Exchange the element with new one in case it has been contaminated. When reinstalling the element to the unit, fit the hook A and the hole, and then inset the element to the unit. (1) Hooks (2) Air cleaner element (3) Hole (4) Hook A (5) Hook B Make sure that the hook A is correctly fit with the hole to reduce the chance of damage of the hook A. 2. Fuel filter Using a wire hook, take out the filter from th...

Download now

Please, enter two numbers from picture: