Votes - 4, Average rating: 4
(
)
)
|
manual abstract
Clean the air filter. Replace if necessary. Empty the oil tank and clean the inside. Clean the starter units air intake. Check all cables and connections. Check that nuts and screws are tight. Check that the stop switch works correctly. Check that there are no fuel leaks from the engine, tank or fuel lines. On chain saws with a catalytic converter, check the cooling system daily. English – 35 TECHNICAL DATA Technical data 334T 338XPT Engine Cylinder displacement, cu.in/cm3 2,15/35,2 2,38/39 Cylinder bore, inch/mm 1,50/38,0 1,57/40 Stroke, inch/mm 1,22/31 1,22/31 Idle speed, rpm 2800 2800 Power, kW/ rpm 1,5/9600 1,7/9600 Ignition system Manufacturer of ignition system SEM SEM Type of ignition system CD CD Spark plug NGK BPMR 7A/ NGK BPMR 7A/ Champion RCJ 7Y Champion RCJ 7Y Electrode gap, inch/mm 0,02/0,5 0,02/0,5 Fuel and lubrication system Manufacturer of carburetor Zama Zama Carburetor type C1Q EL33 C1Q EL33 Fuel tank capacity, US pint/litre 0,72/0,34 0,72/0,34 Oil pump capacity at 8,500 rpm, ml/min 3-7 3-7 Oil tank capacity, US pint/litre 0,30/0,14 0,30/0,14 Type of oil pump Automatic Automatic Weight Chain saw without bar or chain, empty tanks, lb/kg 7,7/3,5 7,7/3,5 Chain/bar Standard bar length, inch/cm 14"/34 14"/34 Recommended bar lengths, inch/cm 12-14”/30-35 12-16”/30-40 Usable cutting length, inches/cm 11-13”/28-33 11-15"/28-38 Chain speed at max. power, m/sec 18,3 18,3 Pitch, inch/mm 3/8 / 9,52 3/8 / 9,52 Thickness of drive links, inch/mm 0,050/1,3 0,050/1,3 Number of teeth on drive sprocket 6 6 36 – English TECHNICAL DATA Recommended original and replacement bar and chain combinations Following is a list of recommended cutting equipment for the Husqvarna chain saw models 334T and 338XPT. The combinations of power head, bar and chain have been tested and found to be in accordance with the kickback and vibration requirements of ANSI B175.1–2000. The guide bar nose radius is determined by either the maximum number of teeth in the nose sprocket or the corresponding maximum nose radius of a hard nose. The following list is the chain saw manufacturers recommendations. There may be other combinations available, which will also achieve kickback reduction. As we are listing the maximum guide bar nose radius, you may use a guide bar with smaller nose radius than in our list. For guide bars of the same length, all sprocket-nose guide bars of the same pitch and having the same number of sprocket teeth may be considered to have equivalent kickback energy. A hard nose bar having the same length and nose radius as a sprocket-nose bar may be considered to have equivalent or less kickback energy than the sprocket-nose bar. Low kickback saw chain is a chain which has only met the kickback performance requirements of ANSI B 175.1 safety requirements for gasoline powered chain saws when tested on the representative sample of chain saws below 3.8 cu. in. specified in ANSI 175.1.We recommend that you as a replacement use the listed chains or "Low kickback saw chains" which are available at your dealer. Bar and chain combinations, model 334T Bar Chain Length, inch Pitch, inch Gauge, inch Max. nose radius Type Drive link count 12 3/8 1,3 7 T Husqvarna H36 45 14 3/8 1,3 7 T 52 Bar and chain combinations, model 338XPT Bar Chain Length, inch Pitch, inch Gauge, inch Max. nose radius Type Drive link count 12 3/8 1,3 7T 45 14 3/8 1,3 7T Husqvarna H36 52 16 3/8 1,3 7T 56 Saw chain filing and file gauges English – 37 FEDERAL AND CALIFORNIA EMISSIONS CONTROL WARRANTY STATEMENT YOUR WARRANTY RIGHTS AND OBLIGATIONS The EPA (U.S. Environmental Protection Agency), CARB (California Air Resources Board), Environment Canada and Jonsered are pleased to explain the emissions control system’s warranty on your 2009 and later small off-road engine. In U.S. and Canada, new equipment that use small off-road engines must be designed, built, and equipped to meet the applicable Federal or Californian stringent anti-smog standards. Jonsered must warrant the emissions control system on your small off-road engine for the period listed below provided there has been no abuse, neglect or improper maintenance of your equipment.Your emissions control system may include parts such as the carburetor, ignition system, catalytic converter, fuel tank, filters and other associated components. Also, included may be hoses, belts, connectors, sensors, and other emission-related assemblies. Where a warrantable condition exists, Jonsered will repair your small off-road engine at no cost to you including diagnosis, parts and labor. MANUFACTURER. .... S WARRANTY COVERAGE The emissions control system is warranted for two years. If any emissions-related part on your equipment is defective, the part will be repaired or replaced by Jonsered. OWNER. .... S WARRANTY RESPONSIBILITIES • As the small off-road engine owner, you are responsible for performance of the required maintenance listed in your operator’s manual. Jonsered recommends that you retain all receipts coverin...