("Raypak") warrants to the original owner that all parts of this boiler which are actually manufactured by Raypak will be free from failure under normal use and service for the specified warranty periods and subject to the conditions set forth in this Warranty. Labor charges and other costs for parts removal or reinstallation, shipping and transportation are not covered by this Warranty but are the owner's responsibility. HEAT EXCHANGER WARRANTY: Five (5) years from date of boiler installation

WHAT DOES THIS LIMITED WARRANTY NOT COVER? This warranty applies only to heaters installed for SINGLE FAMILY RESIDENTIAL APPLICATIONS. (Heaters installed for commercial, multi-family and other uses will be warranted for a period of one year from date of installation.) It does not apply if the pool heater is installed in violation of any applicable code or ordinance, or is not installed, operated and maintained in accordance with our instructions, or is misused, damaged by accident, weather, act

Your results may vary. Economaster Circuit Board Catalog No.: 5100.20-I Effective: 12-28-07 Replaces: 03-15-03 ELECTRICAL DATA Adjustable Timing: 3 to 10 minutes (Factory set at 7 minutes) Input Power (Primary): 24 VAC 50/60 Hz Input Signal (Controller): 24 VAC or 120 VAC Output (SPST Relay): Load - Up to 10 Amp-120 VAC Single Phase* Ambient Temperature: -67°F to +158°F * Motors larger than 3/4 HP and three-phase current require a contactor or motor starter equipped with a 120 VAC coil

It activates the pump as needed to support hot water demand, and shuts the pump down only after evacuating the boiler's residual heat to the heating system or hot water storage tank. The Economaster II saves money in several ways. Electrical costs are reduced, since the pump is not running constantly. In addition, gas costs are cut, because residual heat that would otherwise escape through the flue is captured, and water is not subject to cooling during unnecessary circulation through the syste

If carton or any filter components are damaged, notify freight carrier immediately. 2. After inspection, carefully remove filter components from carton — filter tank, gauge, air bleeder. 3. Place the filter in its permanent location on a level slab, preferably concrete poured in a form or on a platform constructed of concrete block or brick. DO NOT use sand to level the filter and pump mounting as it may wash away, leaving the unit out of level. During operation this condition will cause vibra

Securely mount this lamp to a stable surface that is safely away from combustible materials of any kind. 3. DO NOT replace the halogen bulb with a wattage higher than what this lamp is rated for. Doing this could cause the lamp parts to melt or catch on fire. 4. To prevent electrical fires or electrocution, DO NOT allow any liquid to come in contact with the lamp. 5. To avoid the risk of burns or electrocution, turn the lamp OFF, unplug it from the power source, and allow it to cool before ma

We recommend bypassing the heat exchanger while adjusting water chemistry. Stabilize chemistry to a pH of 7.2 - 7.8, with chlorine residual at 1.0 to 3.0 ppm. Damage to the heat exchanger due to improper water chemistry is not covered under the warranty. MAXI-FLO SWIMMING POOL HEAT EXCHANGERS Model WMPH-95 PVC Stainless Steel (minimum 10" long) Heating zone supply CD Щ Heating zone return c 0) Stainless Steel (minimum 10" long) ($ To the pool (5) PVC h® 1. Maxi-Flo Heat Exch

Installation of a 12 Volt transformer is required when installing the 12 Volt model of this light. The transformer must be located: • at least 10’ from the pool wall, • installed near a grounded, 3-prong, 120V, GFCI protected outlet. If you do not have a GFCI protected outlet, have a qualified electrician install one. Do not use a 3-prong adapter. The adapter voids the grounding of the system. Do not cut the grounding pin. Do not use an extension cord! Purchase a light with a longer cord. 1. Be