Votes - , Average rating:
(
)
)
Manafacture: Dolphin Peripherals
File size: 1.59 mb
File name: 8e27e776-0a72-48e6-b101-edae88981a5f.pdf
Language of manual:
The document is loading, please wait
 |
The document is loading, please wait
manual abstract
(3 m.) Fig C Fig Fig C 22 3 B C FigFig C 1 1 4 A D B 1 2 3 4 A Fig Minimum 10 ft. (3 m.) Fig C Fig Fig C 22 3 B C FigFig C 1 1 4 A D B 1 2 3 4 Read carefully before using your DOLPHIN dx 5 Battery Robot Pool Cleaner 1) Safety 1.1Charger positioning: The Caddy and Charger [1 page-10] should be positioned at a minimum distance of 10 Ft. (3 m.) from the edge of the pool. Caution:The Charger should be placed in the shade. 1.2) Electrical requirements: Factory-wired for either 100V, 115V or 230V mains supply, the voltage rating should be checked before connection. Ensure that the mains/line outlet is protected by a ground fault interrupter (GFI) or earth leakage interrupter (ELI). Use only the original DOLPHIN Charger. Warning! DO NOT ENTER THE SWIMMING POOL WHILE THE DOLPHIN IS IN OPERATION. 2) DOLPHIN Set-Up 2.1) Caddy Assembly Please follow these instructions and refer to the attached diagram when assembling your Caddy. [Fig. O, page-9]. • Connect the wheel assembly [c-1 page-9] by firmly inserting it into the groove at the bottom of the base. Ensure that it is centered, with a washer [c-2 page-9] on each side. • Remove the two locking plates at the bottom of the base to lock the wheel assembly in place. • Connect the two straight pipes [c-3 page-9] onto the bottom of the handle with the horns [c-4 page-9]. They should "click" into position. Note:There are 2 small holes at each end of both pipes. The holes, which are located at a longer distance from the edge of the pipe, must be inserted into the handle. • Insert the assembled straight pipes and handle into the apertures in the tower until they both "click" and lock into position at the base of the tower [c-5 page-9]. • Fasten the plastic charger [c-6 page-9] to the Caddy tower by fitting the slots in the back of the Charger's handle over the "T" pins in the tower. Press down firmly until the base of the Charger fits onto the tower base. • Clip the pike holder [c-7 page-9] onto the Caddy. • Clip the pike [c-8 page-9] onto the Caddy straight pipe with black base to create a pike pole. • Attach the assembled pike pole onto the pike holder and onto the pike base. • Clip the Caddy float holder [c-9 page-9] onto the Caddy. • Place DOLPHIN on the Caddy. • Place float [2 page-10] in the float holder. Important:Ensure that the float switch is in an OFF position. • Connect the enclosed charging cable [3 page-10] to the Charger. 2.2) Handle The DOLPHIN features an adjustable handle [4 page-10] that is fitted into slots on each side of the DOLPHIN body. After the unpacking of the DOLPHIN from its carton box, the handle must be locked in a diagonal position across the top of the DOLPHIN body in order to ensure optimum cleaning results. Press downwards on each latch [5 page-10] to move independently each handle arm [Fig B]. The two latches feature two round slots [6 page-10] [Fig C], which enable the setting of the handle arm at different positions with varying angles. The normal angle positions of the handle [Fig C-1] will provide the fastest possible waterline sideways movement. The positions in Fig C-2 will provide the slowest waterline sideways movement. 2.3) Remote Control Unit (R.C.U.) Remote Control Unit requires two 1.5 V AAA batteries (included). The R.C.U. is splash-proof only. Keep it away from direct sunlight or rain. This R.C.U. is equipped with a digital screen, soft touch buttons and a Joystick for manual operation. 2 3) Operation . At the front section of the Charger there are indication lights that indicate when the DOLPHIN's battery is charging Reset+ 3.1) The Chargerand when the battery is fully charged. Red light will blink when the battery is charging. Green and Red lights will blink after the battery is nearly fully charged. Green light stays constantly lit after the battery charging is completed. Yellow light will blink when the filter bag needs cleaning. It will remain lit when the filter bag is clogged and needs washing. Used to reset the filter bag indicator in case the light stays lit after filter bag clean up or wash up. This button is also used to initiate Long Term Charging Mode when charging the battery for long term storage. (See point 3.3 for more details) Note:The filter bag indication light is a recommendation. For best DOLPHIN performance, it is recommended to clean the bag when filter bag light turns ON. The DOLPHIN pool cleaner and Charger have been designed for safe, maintenance-free outdoor use. Important safety instruction:Do not use with or connect the charger to any other appliance. Caution:The Charger and the float should be placed in a cool and shaded area. Charging quality and battery longevity will be adversely affected if ambient temperatures either exceed 90°F or drop below 41°F (32°C - 5°C). Bring Charger to an ideal temperature range of 41°F to 90°F (5°C to 32°C). 3.2) Charging of DOLPHIN Battery USE ONLY ORIGINAL DOLPHIN CHARGER! Important Notes: • The DOLPHIN should be charged before its first in-pool use. (Also refer ...