Votes - 3, Average rating: 3
(
)
)
|
manual abstract
After Ninety Days: Between the ninety-first day and the end of the first year after installation, no allowances will be made for labor for the removal or reinstallation of any soclaimed defective products This warranty covers the Time Master Controller, LX-10 Service Center, VOR-24 Valve Operators, and optional Remote Controls, including all components and parts. It does not include Valves or Sensors. It extends to the first retail purchaser and any subsequent owners of the system. This limited warranty applies only to controls which have been installed and maintained in strict accordance with installation and operating instructions provided by Compool Corporation, using installation hardware supplied and/or recommended in writing by Compool, and to controls which have been connected to the correct supply voltage. This limited warranty does not apply to any controls which have been repaired or altered by anyone other than Compool ora person authorized by it; orwhich have been subject to misuse, neglect or accident; or which have been damaged by wind, freezing or other cause, thing, person or act of God; or which have been subject to damage in transit, during installation,or by someone other than Compool Corporation; or which have been damaged because of a defect in a component or part which is not part of the Compool Control System; or upon which the serial number has been altered, effaced or removed. This warranty gives you specific legal rights and you may also have other rights which vary from state to state. Compool Corpora!ion does not authorize any person to create any other obligation or liability in connection with Compool controls. Compool Corporation makes no warranty of merchantability or fitness for any use. Any implied warranty applicable to Compool controls is limited in duration to the duration of this written warranty. Compool Corporation shall not be liable for consequential or incidental damages resulting from breach of this written warranty or any implied warranty. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation of incidental or consequential damages may not apply to you. To exerclse this warranty, send defective unit, with copy of dated receipt, postage prepaid, to: COMPOOL CORPORATION 599 Fairchild Drive, Mountain View, California 94043-221 7 MEMBER [m599 Fairchild Drive Mountain View California 94043-221 7 N.,,oN.L (415) 964-2201 fie.. POOL INSTITUTt Computerized Pool Systems INSTALLATION INSTRUCTIONS TIME MASTER POOL-SPA CONTROL SYSTEM IMPORTANT SAFETY PRECAUTIONS: All wiring must be performed by a qualified electrician. Basic safety precautions and local codes should be observed when installing and using this electrical equipment. FiEAD AND FOLLOW ALL INSTRUCTIONS EQUIPMENT LOCATION: All electrical equipment must be located five feet or more from pool or spa with the exception of the optional Spa-side Remote Control 1. LX-10 Service Center at t!le equipment pad area 2. Time Master inside house or other weather-protected area 3. VOR-24 Valve Opemtors at threeport valves 4. WS5L Water Sensor at filter pump 5. SS100 Spaside Remote Control (optionar) at spa site LOW VOLTAGE CABLES: Determine lengths of 22AWG low voltage cable needed between equipment 1. 6pair cable from Time Master to LX-10 Service Center. 2. 2 conductor cable from gas heater to LX-10 Service Center. 3. Water Sensor is provided with 10 feet of 2 conductor cable. 4. Valve Operators are provided with 15 feet of 3 conductor cable 5. Spa-side Remote Control is provided with 100 feet of 4 conductor cable Remote Control is also available with 50. 150 or 200 feet of cable Install cable. Place cable in plastic or metallic conduit where it runs underground ihrough concrete, etc NOTE: Never install low voltage cable and high voltage wires in the same conduit A minimum distance of 12" must be maintained between parallel runs of low voltage cable and AC current-carrying wires. 22AWG cable is available from Compool Corporation PLUMBING: Fol!ow recommended schematic (see next page) for location of threeport valves 2" dia. plumbing is advised to ensure optimum filter pump efficiency. 1. A Y2" spa makeup line, (incorporating a Y2" manual gate or ball valve and, for elevated spas, aY2" checkvalve) should be provided around the retum valve(see schematic). This enables clean water to be circulated to the spa while the system is in POOL mode 2. Spa should be at or above the level of the pool If spa is attached to pool provide a dam between the two bodies of water to allow spa overflow into pool If spa is not attached to pool an overflow, sufficient in size to carry full pumpflow, must be installed at water level in the spa HYDRAULIC AND ELECTRICAL SCHEMATIC llME CONTROL rlru CLNR SPA wxI TLNCLNI SPA WXI TIME CONlllOL FLlUUH SM WXI SAMPLE PROGRAM: In the adjacent examples 1P. The first program will turn on the filter at 7:40 am. 2P: At 10:OO arq the filter pump will continu...