Votes - 3, Average rating: 4
(
)
)
|
manual abstract
Figure 4. CS50.4 amplifier in 4-channel (stereo) operation to drive front and rear full-range speakers. Figure 5. CS50.4 is set up for 3-channel operation to drive a set of full-range speakers and a subwoofer. Figure 6. CS50.4 used in bridged 2-channel mode to drive a set of components or subwoofers. Set crossovers according to application. APPLICATIONS – CS50.4 The CS50.4 can be set up for stereo 4-channel, 3-channel or bridged 2-channel operation, as shown in Figures 4 through 6. NOTE: For simplicity, Figures 4 through 6 do not show power, remote and input connections. NOTE: Minimum speaker impedance for stereo operation is 2 ohms. Minimum speaker impedance for bridged operation is 4 ohms. CONTROLS AND SETUP SPECIFICATIONS Declaration of Conformity SETTING THE CROSSOVER(S) Determine your system plans and set the crossover mode switch accordingly. If your system design does not include a subwoofer with the CS50.4, set the crossover mode to FLAT and skip to “Setting Input Sensitivity.” Initially set the crossover frequency control midway. While listening to music, adjust the crossover for the least perceived distortion from the speakers, allowing them to reproduce as much bass as possible. SETTING INPUT SENSITIVITY 1. Initially turn the INPUT LEVEL control(s) to minimum (counter clockwise). 2. Reconnect the (–) negative lead to the vehicle’s battery. Apply power to the audio system and play a dynamic music track. 3. On the source unit, increase the volume control to 3/4 volume. Slowly increase the INPUT LEVEL control(s) toward three o’clock until you hear slight distortion in the music. Then reduce the INPUT LEVEL slightly until distortion is no longer heard. CS200.1 • 236W RMS x 1 channel at 4 ohms and .1% THD + N • Signal-to-noise ratio: 100dBA (reference 1W into 4 ohms) • 338W RMS x 1 channel at 2 ohms, 14.4V supply and .1% THD + N • Dynamic power: 464W at 2 ohms • Effective damping factor: 6.395 at 4 ohms • Frequency response: 10Hz – 302Hz (–3dB) • Maximum input signal: 7.5V • Maximum sensitivity: 260mV • Output regulation: .073dB at 4 ohms • Dimensions (L x W x H): 12" x 10" x 2-1/4" • Fuses: 20A x 2 We, Harman Consumer International 2, route de Tours 72500 Chateau-du-Loir France declare in own responsibility that the products described in this owner’s manual are in compliance with technical standards: EN 55013:2001 EN 55020:2002 Emmanuel Millot Harman Consumer International Chateau-du-Loir, France 3/04 CS50.4 Systems using a separate subwoofer set NOTE: After the source unit is on, blue • 67W RMS x 4 channels at 4 ohms and .1% THD + N JBL Consumer Products the crossover mode to HP (high pass) for LEDs (on the top panel) will light, indicating your full-range speakers. Adjust the the amplifier is on. If not, check the wiring, • Signal-to-noise ratio: 86dBA (reference 1W into 4 ohms) 250 Crossways Park Drive, Woodbury, NY 11797 USA crossover frequency to limit bass and especially the remote connection from the • 82W RMS x 4 channels at 2 ohms, 14.4V supply and .1% THD + N provide increased system volume with source unit. Also refer to “Troubleshooting” • 162W RMS x 2 channels at 4 ohms, 14.4V supply and .1% THD + N © 2004 Harman International less distortion. guide below. Industries, Incorporated • Dynamic power: 145W at 2 ohms • Effective damping factor: 6.395 at 4 ohms JBL is a registered trademark For subwoofers, choose the highest of Harman International • Frequency response: 10Hz – 27kHz (–3dB) frequency that removes vocal information Industries, Incorporated. from the sound of the subwoofer. • Maximum input signal: 6V Part No. CSAMPOM3/04 • Maximum sensitivity: 240mV If using the CS50.4 to drive a subwoofer(s), • Output regulation: .032dB at 4 ohms set the crossover mode to LP (low pass). • Dimensions (L x W x H): 12" x 10" x 2-1/4" • Fuses: 25A x 2 TROUBLESHOOTING SYMPTOM LIKELY CAUSE SOLUTION SYMPTOM LIKELY CAUSE SOLUTION No audio No voltage at BATT+ Check voltages at (POWER LEDs or REM terminals, amplifier terminals are off) or bad or no ground with VOM connection No audio Amplifier is (POWER overheated LEDs are on) Make sure amplifier cooling is not blocked at mounting location; verify speaker-system impedance is within specified limits No audio Voltage less than 9V on (POWER BATT+ connection LEDs flash) DC voltage on amplifier output Check vehicle charging system Amplifier may need service; see enclosed warranty card for service information Distorted audio Input sensitivity is Check INPUT not set properly, or LEVEL setting; or amplifier or source check speaker wires unit is defective for shorts or grounds Voltage more than 16V Check vehicle Distorted audio Short circuit in Remove speaker leadsor less than 8.5V on charging system and POWER speaker or wire one at a time to locate BATT+ connection LEDs flash shorted speaker or wire, then repair Music lacks Speakers are not Check speaker “punch” connected properly connections for proper polarity Features, specifications and appearance are subject...