Votes - 1, Average rating: 4 ( )

Manafacture: Earthquake Sound File size: 1.05 mb File name: Language of manual:

LOW LEVELINPUTS: Low level inputs range of 0.2V to 5V RMS. This is where the front and rear RCA outputs from your head unit or other devices are inserted. with a R C A l i n e t h r o u g h t o c a s c a d e a n o t h e r amplifier. N o X o v e r point. 2-WAY 12dB/Oct VARIABLE XOVER: C o n t r o l t h e corresponding channels cutoff frequencies. This feature is disabled when in FULLRANGE This information applies to both HPF and LPF FC6.2 FC6.2 FC6.2 Xover FC6.2 Xover FC6.2 Midrange FC6.2 Midrange AUTO SIGNAL SENSING: Please refer to page 3 for explanat ion of thi s feature. HIGH LEVEL INPUT: Speaker level inputs with a range of 0.5V to 17V RMS. BASS BOOST: 0 - 18dB Bass Boost for use w i t h subwoofers. AUTO ON RESET REMOTE ON POWER LED: When LED is on, it indicates that the amplifier is ON and f u n c t i o n i n g properly. PROTECTION (PROT) LED: If LED comes on then you have an issue that requires service. Turn off the amplifier and call Earthquake for further assistance. See warranty for details. Specifications Are Subject To Change Without Notice 8 9 T1000W/2 Set Xover switch to FULL K-10, ten-inch bass tube, in mono application (4 Ohms minimum) Two 25A fuses To car chassis / ground To remote turn on / trigger To battery positive (+) Bridgeable Speaker outputs, minimum 4-Ohms mono. 7.0V 17.0V 4.0V 10.0V 2.5V 5.0V 1V 1V The gain knob is not a volume control. It is designed to match the input level of the amp to the output level of the source unit. Over driving "clipping" the input stage of the amp will cause damage to the amplifier (please refer to table for setting). MAX INPUT VOLTAGE BEFORE CLIPPING RCA LEVEL SPEAKER LEVEL XOVER KNOB SETTING T1000W/2 50Hz 90Hz 125Hz 170Hz 210Hz 250Hz FC6.2 Tweeter FC6.2 Tweeter FC6.2 Xover FC6.2 Xover FC6.2 Midrange FC6.2 Midrange AUTO ON RESET REMOTE ON LOW LEVELINPUTS: Low level inputs range of 0.2V to 5V RMS. This is where the front and rear RCA outputs from your head unit or other devices are inserted. with a AUTO SIGNAL SENSING: Please refer to page 3 for explanat ion of thi s feature. MODE SELECTOR: This feature tells the amplifier to run in either HIGH PASS, FULL RANGE or LOW PASS MODE LEVELADJUST: Allows the amplifier to deliver a controlled maximum sound level into selected channel(s) when the volume is turned to max. This acts as a volume limiter for the system, preventing you from over driving the speakers or subwoofers. R C A l i n e t h r o u g h t o c a s c a d e a n o t h e r amplifier. N o X o v e r point. 2-WAY 12dB/Oct VARIABLE XOVER: C o n t r o l t h e corresponding channels cutoff frequencies. This feature is disabled when in FULLRANGE This information applies to both HPF and LPF HIGH LEVEL INPUT: Speaker level inputs with a range of 0.5V to 17V RMS. POWER LED: When LED is on, it indicates that the amplifier is ON and f u n c t i o n i n g properly. PROTECTION (PROT) LED: If LED comes on then you have an issue that requires service. Turn off the amplifier and call Earthquake for further assistance. See warranty for details. Specifications Are Subject To Change Without Notice BASS BOOST: 0 - 18dB Bass Boost for use w i t h subwoofers. 10 11 T2000W/4 Bridgeable Speaker outputs, minimum 4-Ohms mono. Set Xover switch to FULL K-10, ten-inch bass tube, in mono application (4 Ohms minimum) CH3 CH4 CH3 CH4 CH1 CH2 CH1 CH2 To car chassis / ground To remote turn on / trigger To battery positive (+) Two 20A fuses 7.0V 17.0V 4.0V 10.0V 2.5V 5.0V 1V 1V The gain knob is not a volume control. It is designed to match the input level of the amp to the output level of the source unit. Over driving "clipping" the input stage of the amp will cause damage...

Download now

Please, enter two numbers from picture: