Login:
Votes - 3, Average rating: 4.3 ( )

User manual Interfire Audio, model AUTOMOTIVE AMPLIFIER G2-800

Manafacture: Interfire Audio
File size: 495.19 kb
File name:
Language of manual:en
Free link for this manual available at the bottom of the page



manual abstract


advisable to prevent straining or breakage. to normal. qualified mechanic. with each other. Speaker wire should be 18 gauge or larger. accessory. If the amplifier does not turn off the battery will die. INSTALLATION MOUNTING: 1. After reading precaution, decide where you are going to install the unit. Also, see Fig.1. 2. Once the location has been determined, place the amplifier into position. Using a felt tip pen or pencil mark the four holes to be drilled for mounting. NEVER use the amplifier as a template for drilling. It is very easy to damage the amplifier surface in this manner. 3. Remove amplifier. Drill four 3.5 m/m holes into mounting surface. If you want to mount the amplifier to MDF or wood panel, drill four 3.0m/m diameter holes into mounting surface. 4. If possible, test the system to ensure it is operating correctly before final mounting of 5. INSTALLATION DIAGRAM Mount the amplifier using the supplied 4 self tapping screws. the amplifier. Self Tapping Screws FIG.1 3 CONNECTIONS INPUT CONNECTIONS This amplifier will accept low level inputs only. Low level is the same as line level. The low level signal is carried through RCA cables. It is preferred to use low level inputs to the amplifier if the head unit is equipped with the low level outputs. If not, you can use a "high to low converter" available through your local car audio shop. Connect the low level/line level RCA cables from the head unit, or signal processor, to the line level input on the amplifier. See Fig.2 system wiring diagrams. POWER CONNECTIONS It is important to have good quality power and ground connections. Remember, to complete an electrical circuit, the ground connection is just as important as the positive power connection. Before any power connections are made, disconnect the ground cable at the battery. When the power supply lead, memory backup lead or ground lead are extended use a 5mm. (AWG5) or larger automotive grade cable which will withstand friction and heat to safe grade against fires occurring as a result of short-circuiting. GND = Connect the proper gauge ground wire to the amplifier "GND" terminal. Locate the position on the chassis of the car to which the amplifier is to be grounded. The surface must be free from any paint or dirt. This can be accomplished with a small grinding bit, sand paper or wire wheel. NOTE: Do not ground the amplifier to the "frame of the car. The frame on most cars and trucks is not grounded to the chassis(body). Use Solder or a clamp ring to connect the ground wire. Pre-drill the prepped chassis to bolt the ground ring terminal with nut, bolt and lock washers. Insulate metal and connector with paint or silicon to prevent rust and oxidation. Silicon also works great to prevent nuts and bolts from working loose in a harsh environment of an automobile. Upon completion of the ground connection, grab wire or connector and confirm that it is a solid connection. To prevent engine noise, it is recommended to ground the head unit and other audio electronics in the same location. likely be a dead battery. 12V = Connect the proper gauge power wire to the amplifier "B+" terminal. Run wire to wards the fuse holder that is no greater then 0.5 meters from the battery. Remember, the fuse is to protect the safety of the car in the case of a short. Connect fuse holder to battery, but do not install fuse at this time. 4 REM = Connect the remote wire (power antenna output) from the head unit to the remote turn-on wire of the amplifier. If the head unit is not equipped with a remote/antenna output, locate a wire that is controlled by...

Other models in this manual:
Car Amplifiers - AUTOMOTIVE AMPLIFIER G2-1200 (495.19 kb)
Car Amplifiers - AUTOMOTIVE AMPLIFIER G2-600 (495.19 kb)
Car Amplifiers - AUTOMOTIVE AMPLIFIER G4-1000 (495.19 kb)
Car Amplifiers - AUTOMOTIVE AMPLIFIER G4-600 (495.19 kb)

Reviews



Your review
Your name:
Please, enter two numbers from picture:
capcha





Category