Votes - 5, Average rating: 4 ( )

Manafacture: Panasonic File size: 2.16 mb File name: Language of manual:

¦ To establish a conference call: Press {CONF}. L To leave the conference, press {OFF}. The other parties can continue the conversation. L To put the outside call on hold, press {HOLD}. To resume the conference, press {CONF}. Transferring a call without speaking to the other handset or base unit user = Base unit 1 Proceed with the desired operation. ¦ When 1 handset is registered: During an outside call, press {INTERCOM}. ¦ When 2 or more handsets are registered: During an outside call, press {INTERCOM}. – To page a specific handset, enter the handset number. – To page all handsets, press {0} or wait for a few seconds. 2 Place the corded handset on the cradle. L The outside call rings at the other unit. Y Handset 1 During an outside call, press {HOLD} to put the call on hold. L To return to the outside call, press {BACK}. 2 To page the base unit, press {0}. To page another handset, enter its extension number. 3 {OFF} L The outside call rings at the other unit. Note for base unit and handset: L If the other user does not answer the call within 1 minute, the call rings at your unit again. Answering a transferred call = Base unit Lift the corded handset or press {SP-PHONE} to answer the page. Y Handset Press {C} to answer the page. Note for base unit and handset: L After the paging party disconnects, you can talk to the outside caller. For assistance, please visit Useful Information 40 For assistance, please visit Wall mounting Base unit 1 Connect the AC adaptor and telephone line cord. Tuck the telephone line cord inside the wall mounting adaptor, then push it in the direction of the arrow. L The word “UP” should face upward. 2 Connect the telephone line cord. Mount the unit by inserting the mounting pins into the round openings on the adaptor (for pin 2, use the round cut out at the bottom of the adaptor if you are using the 4 inch phone plate), then slide the unit down to secure it. Connect the AC adaptor to power outlet (page 8). L There are 2 common types of wall phone plates. The distance between 1 and 2 may vary depending on the size of the wall phone plate installed. Charger 1 Drive the screws (not supplied) into the wall. 2 Mount the charger (A), then slide it down (B) and to the right (C) until it is secure. Belt clip ¦ To attach ¦ To remove 25.4 mm (1 inch) Screws (120 V AC, 60 Hz) A B C Useful Information Error messages If the unit detects a problem, one of the following messages is shown on the display. Display message Cause/solution Busy L The called unit is in use. L Other units are in use and the system is busy. Try again later. L The handset you are using is too far from the base unit. Move closer and try again. L The handset’s registration may have been canceled. Reregister the handset (page 27). Check tel line L The supplied telephone line cord has not been connected yet or not connected properly. Check the connections (page 8). Error!! L Recording was too short. Try again. Failed L Phonebook copy failed (page 19). Confirm the other unit (the receiver) is in standby mode and try again. Incomplete L Phonebook copy is incomplete. The receiver’s phonebook memory is full. Erase the unnecessary phonebook entries (page 17) from the other unit (the receiver) and try again. Memory full L The phonebook memory is full. Erase unnecessary entries (page 17). L Message memory is full. Erase unnecessary messages (page 32, 33). Messages full L Message memory is full. Erase unnecessary messages (page 32, 33). No link. Reconnect base AC adaptor. L The handset has lost communication with the base unit. Move closer to the base unit and try again. L Unplug the base unit’s AC adaptor to reset the unit. Reconnect the adaptor and try again. L The handset’s registration may have been canceled. Reregister the handset (page 27). Requires subscription toCaller ID. L You must subscribe to a Caller ID service. Once you receive caller information after subscribing to a Caller ID service, this message will not be displayed. Use rechargeable battery. L A wrong type of battery such as Alkaline or Manganese was inserted. Use only the rechargeable Ni-MH batteries noted on page 4, 5. For assistance, please visit Useful Information Troubleshooting If you still have difficulties after following the instructions in this section, disconnect the base unit’s AC adaptor, then reconnect the base unit’s AC adaptor. Remove the batteries from the handset, and then insert the batteries into the handset again. General use Problem Cause/solution The unit does not work. L Make sure the batteries are installed correctly (page 8). L Fully charge the batteries (page 8). L Check the connections (page 8). L Unplug the base unit’s AC adaptor to reset the unit. Reconnect the adaptor and try again. L The handset has not been registered to the base unit. Register the handset (page 27). I cannot hear a dial tone. L The base unit’s AC adaptor or telephone line cord...

Download now

Please, enter two numbers from picture: