. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 Safety Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 About This Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6 Main Unit Button Functions . . . . . . . . . . . . . . . . . . . . . . . . .7 Remote Control Button Functions . . . . . . . . . . . . . . . . . . . .9 Main Unit Connection

The battery’s negative terminal must be disconnected for the entire time it takes to install and connect this device. When doing so, observe the vehicle manufacturer’s safety notices (airbags, alarm systems, trip computers, immobilizers). Before drilling any holes, make sure that no installed cables or vehicle components can be damaged. When installing the signal controller, select a location in the vehicle that allows you to attach it firmly into place using screws. The installation location sh

Note: Before connecting the monitors to your signal controller, check that the +/- and switching positive connections are working properly. Positive connection Connect the fuse holder (1A fuse) to protect the positive cable (permanent (1), see Fig. 1). The fuse holder should be connected to the positive terminal at a distance of max. 30 cm from the vehicle battery (if necessary, drill a hole in the bulkhead and use the appropriate cable grommets). Switching positive Connect the switching positiv

27 Specifcations ......................... 28 IVMR-9002.................................... 28 IVMR-1042.................................... 29 CONTENTS 19 ENGLISH NOTES FOR THE USER Thank you for choosing a Blaupunkt product. We hope you enjoy using this new piece of equipment. Please read these operating instructions before using the equipment for the first time. The Blaupunkt editors are constantly working on making the operating instructions clearer and easier to understand. However, if you

Warning notice: The operating voltage cable must be protected with at least a 1.5 A fuse. Monitor connection (13 pin) Connect the system cable (13 pin) > to a signal controller (IVSC-3302 or IVSC-5502). (The voltage supply is provided by these devices. Operating instructions are supplied with the devices). Or Use the plug-in adapter cable ? to connect to the 12 V supply voltage and an external video/DVD device: Red = +12 V direct current Black = Earth Red RCA = Audio IN (R) White RCA = Audio IN

. Then attach the Velcro strips to the rear of the monitor, and push the frame onto the headrest. Take care not to press the screen itself, and apply pressure only in the region of the frame. Example of a direct connection to a DVD player Adapter cable for a direct connection to an AV source DVD - Player (IVDP-01) Video outAVDigital inout Audio L outAudio R out Masse/GND +12V IVMS 5802/6502 Positive connection Connect the fuse holder to protect the positive cable (+12 V). The fuse holder should

The manufacturer cannot accept responsibility for any damage caused as a result of improper fitting of this device. To avoid the risk of electrical shock, the device must be protected from water and moisture, and must not be opened. Dangerously high voltages are generated inside the device. We wish to point out that the right to claim against warranty is invalidated by any changes or modifications to the device that have not been explicitly approved by the manufacturer. Long-term operation or st

14 Prepare the working area .............. 14 Mark out the dimensions................ 15 Carefully cut open the headrest cover ............................................. 15 Open the headrest and remove filling and other items ..................... 15 Lay the cable through the headrest ........................................ 16 Insert the mounting frame in the headrest .................................. 16 Insert the monitor .......................... 16 Check and adjust the monitor then appl

To remove the screen, insert the extraction tool between the screen and the mounting plate. . Insert the extraction tool at the place where a slot has been provided between the screen and the mounting plate. Extraction tool ENGLISH 17 FUNCTION OSD functions Main menu . Call up the main menu by pressing the “MODE” key on the main device, or “MENU” on the remote control unit. . Select the “EXIT” option to leave the OSD menu again. VOLUME BRIGHTNESS CONTRAST COLOR TINT MISC EXIT + Sub-menu . To rea

18 Using for the first time ........... 19 Using the interior light .................... 19 Changing the light bulb ................. 20 Light bulb specifications ................ 20 Wiring ........................................... 20 Monitor connection ........................ 20 Installing the monitor...................... 21 Operation ............................... 22 Opening the monitor ...................... 22 Repositioning the monitor .............. 22 Closing the monitor .............