Votes - 3, Average rating: 4
(
)
)
|
manual abstract
An LCD panel or video monitor used for television reception, video or DVD play that operates when the vehicle is in gear or when the parking brake is not applied must be installed to the rear of the driver’s seat where it will not be visible, directly or indirectly, to the operator of the motor vehicle. It is unlawful in most jurisdictions for a person to drive a motor vehicle which is equipped with a screen that is located in the motor vehicle at any point forward of the back of the driver’s seat, or that is visible, directly or indirectly, to the driver while operating the vehicle. In the interest of safety, the MM850 should never be installed where it will be visible, directly or indirectly, by the operator of the motor vehicle. Licensed under one or more of the following patents, Patent NOS. 5,775,762 and 5,927,784 3 Installation Guide MATERIALS INCLUDED IN THIS PACKAGE: 1) MMD85 Video Monitor with DVD player (P/N136D3586) (1 pc) 2) A/V Adapter Cable (112B3227) (1 pc) 3) 2 Pin Power Wire Harness with choke (P/N112B3370) (1 pc) 4) Hardware Package:- ¦ #8 x 3/4” Self Drilling Screws (4 pcs) ¦ #8 Washers (4 pcs) 5) Dome light Harness (112B3110) (1 pc) 6) Remote Control (136B3591) (1pc) TOOLS REQUIRED: #2 Phillips Screwdriver #1 Phillips Screwdriver Utility or Razor Knife or Shears Wire Strippers Upholstery hook tool (for removal of panels as necessary) Electrical Tape Masking Tape Multimeter (to verify 12 volt DC and continuity: Do not use a test light or logic probe) Marker pen – to mark headliner Scribe (to mark trim ring if used) Misc. electrical connectors (to connect to vehicle power source). Requirements will vary from vehicle to vehicle. 35 1. 2. 3. 5. 6. 4. CHOKE 1 2 3 4 5 6 7 8 9 0 ENTER VEHICLE PREPARATION: 1) Locate an accessory power source (+12v when key is in the ACC. and run positions, and 0v when key is off). Also find a location that will provide a good grounding point. Generally, this wire can be found at the ignition switch or fuse-box. 2) The mounting method and location will vary from vehicle to vehicle, so this manual will only focus on the installation of the video monitor and related accessories. 3) Generally, the best location for the video monitor is where the vehicle's factory dome light is installed. The monitor should be located in such a manner that it can be comfortably viewed by rear seat passengers. NEVER INSTALL THE MONITOR IN A PLACE WITHIN THE DRIVER'S VIEW. THIS IS NOT ONLY DANGEROUS, BUT IT IS ALSO ILLEGAL. 4) Once the mounting location of the monitor has been determined, there may be additional preparation work necessary, depending on the vehicle structure and installation method. Some of the steps that may be required are: A) Removal of the vehicle's dome light B) The headliner may need to be trimmed VIDEO MONITOR INSTALLATION: In this installation, the video monitor is mounted directly to the overhead cross-member in the roof using the mounting screw bosses. These screw bosses should contact the cross-member directly (i.e.: no gap between the screw boss and the roof structure). Also, be sure that the screws do not pierce the outer roof skin when fully fastened to the cross-member. It is important that the screws used in this installation are not overtightened, and that the video monitor is mounted in such a way that the assembly does not distort (or bend) when the mounting screws are tightened. An alternate method is to use a piece of plywood. First secure the plywood block to the cross-member, then screw the monitor into the plywood. See the drawing on page 5. Installation Guide MOUNTING THE VIDEO UNIT Roof Roof support Headliner 5"x9"x3/4" Plywood Block or Optional VOHBKT (4) #8x1" self drilling screws (not supplied) Video unit (4) #8 Flat washers (supplied) (4) #8x3/4" self tapping screws ( supplied) Installation Guide Installation GuideInstallation Guide MMD85 Red/Black (Lamp On) Line Out Right and Left CHOKE Line Out-R (Red) - Line Out-L (White) Line Out-V (Yellow) Power Harness Item # 3 Line In-R (Red) Line In-L (White) Line In-V (Yellow) Violet/Brown (Lamp Auto) Black/Red (Lamp Common) Line Video Out Audio Video Output Audio Video Input Dome Light Power Source 1) Make the connections to the vehicle for the 2 pin wiring harness. 2) Connect the 2 pin harness to the mating connector on the Video Monitor. 3) Connect power harness to vehicle's electrical system by tapping into an accessory hot line and a good ground. 4) Verify all functions of the System before final mounting of the finished assembly. Note: A VCP or other A/V Component can be connected to the video monitor system using the LINE IN RCA jacks. A/V Source Definitions : 1 = Built-in DVD 2 = AV1 input ( VCD, Game or future DVD, etc ) 3 = AUX input ( VCD, Game or future DVD, etc ) CONNECTING THE DOME LIGHTS The dome lights in the video monitor require three connections to the vehicle's wiring. There are two common types of dome light circuits used, positive or negative switched. Positive systems supply ...