1 2 3 Screws (4) Mount the Control Box Secure the control box to mounting surface (post, wall, column, etc.) using appropriate hardware (not provided). Install the Control Board Attach antenna. Reinstall batteries, control board, alarm, and reset button. Reconnect coaxial connector. NOTE: Make sure battery leads are on the left side of the control box and not pinched. Installation 22 4 5 Antenna U-Bolt (Not Provided) Wall Concrete Anchor Square Gate Post Screw 18 L1 K2 Z22 F2 MOV1 D1 OPEN SINGLE

For proper functionality, the limits must be learned during the installation process. The programmed limit process uses a combination of buttons on the control board. The specific buttons used for programming depends on which side of the gates the control box is mounted on and how many operators the installation includes. Refer to pages 11-12 to determine if the gate is Left- or Right-handed and for explanation of PULL-TO-OPEN and PUSH-TO-OPEN. If a mistake is made during the programming process

The use of short neck or speciality light bulbs may overheat the endpanel or light socket. Lens 100 Watt (Max) Hinge Standard Light Bulb 100 Watt (Max) Standard Light Bulb Release Tab INSTALLATION STEP 8 Attach the Emergency Release Rope and Handle • Thread one end of the rope through the hole in the top of the red handle so "NOTICE" reads right side up as shown. Secure with an overhand knot at least 25 mm from the end of the rope to prevent slipping. • Thread the other end of the rope through t

NOTES: Batteries will degrade over time depending on temperature and usage. For best performance, the batteries should be changed every 3 years. Batteries do not perform well in extremely cold temperatures. To reduce the risk of FIRE or INJURY to persons use ONLY LiftMaster part 27-NP712 for replacement batteries. 18 R93 L1 D42 K2 D1 D1O Z22 P1 F2 MOV1 D1 Q12 U4 OFF MAX OPEN SINGLE BUTTON RESET STOP CHGR OVLD COM COM D129 Z4 U3U3 D2 D44 C11 C13 C12 D16 F9 R1OO R1O1 K1 Q22 F3 K4 K3 R196 F1 Z12 GA

¦ The model number label is located inside the control box of your operator. ¦ ¦¦ Serial # ¦ ¦¦ Installation Date TABLE OF CONTENTS 2-7 INTRODUCTION 2 Safety Symbol and Signal Word Review 3 Operator Specifications 4-5 Safety Installation Information 6 Carton Inventory 6 Hardware Inventory 7 Additional Items for Purchase 7 Tools Needed 8-12 PREPARATION AND OVERVIEW 8 Single Gate Overview 9 Dual Gate Overview 10 Check Your Gate 11 Mounting Options 12-21 INSTALLATION 12-18 Attach the Operator to th

• Activate gate ONLY when the gate is in full view and free from any obstructions. • ALWAYS keep gate in sight until completely closed. NEVER permit anyone to cross the path of the moving gate. • ALWAYS keep gate in good repair and make sure it moves freely. An improperly maintained gate may not reverse when required and could result in SEVERE PERSONAL INJURY or DEATH. WARNING 7 41A3489 Trolley 41A4353 Header Bracket 41A3611-2 Chain in Dispensing Carton 178B35 Curved Door Arm Section 178B34 Stra

Pliers Wire Cutters Claw Hammer Hack Saw Screwdriver Adjustable End Wrench Sockets and Wrench Drill Tape Measure 21 Stepladder Pencil 4 mm, 5 mm and 8 mm Drill Bits Carpenter's Level (Optional) 3 Safety Reversing Sensor Support bracket & fastening hardware is required. See page 21. — — — — — — — — Header Wall FINISHED CEILING Torsion Spring Extension OR Spring Safety Reversing Sensor Gap between floor and bottom of door must not exceed 6 mm. Access Door Wallmounted Door Control Horizontal and ve

SECTIONAL DOORS ONLY • Make sure garage door is fully closed. Pull the emergency release handle to disconnect the outer trolley from the inner trolley. Slide the outer trolley back (away from the door) about 5 cm as shown in Figures 1, 2 and 3. • Figure 1: – Fasten straight door arm section to outer trolley with the 5/16"x1" clevis pin. Secure the connection with a ring fastener. – Fasten curved section to the door bracket in the same way, using the 5/16"x1-1/4" clevis pin. • Figure 2: – Bring a

To Add, Reprogram or Change a Keyless Entry PIN NOTE: Your new Keyless Entry must be programmed to operate your garage door opener. USING THE LIGHTED DOOR CONTROL NOTE: These methods requires two people if the Keyless Entry is already mounted outside the garage. 1. Remove the cover from the Lighted Door Control. 2. Enter a four digit personal identification number (PIN) of your choice on the keypad. Then press and hold ENTER. 3. While holding the ENTER button, press and hold the “A” button on th

PAD AND MOUNT _______________________________________________________________________ 4 C. POWER WIRING_________________________________________________________________________ 5 D. LOOP DETECTORS AND PHOTO-SENSORS _________________________________________________ 5 E. TELEPHONE CONNECTION _______________________________________________________________ 5 F. MASTER/SLAVE INTERCONNECTION (MASTER/SLAVE SYSTEM ONLY)_______________________ 5 G. OTHER CONNECTIONS ______________________________________