Votes - 2, Average rating: 4.5
(
)
)
|
manual abstract
TheSR-150 is the product that needs to be selected in the composersoftware. 4 Double-click SR-150 (RC100) to add the device to the project tree. 5 Identify the RC100: a. In the Connections view, go to the Network tab. b. Select Remote Control SR-150 (RC100) in the center pane. c. Click Identify (or right-click and choose Identify). d. When prompted to do so, press the Blue Zone Button on the remote four times to have the device identify itself to the Escient system. Note: To complete the identification process, the remotemust be on the same ZigBee channel as the controller andthe controller must have Zserver enabled. If you need tochange the ZigBee channel on the remote, see step 7. e. Once the MAC address appears in the window, click Close. 6 Change Remote Control properties as needed in Composer: In the System Design view in the project tree (left pane), select the Remote Control SR-150 (RC100) object to display the remote’s properties. The modifiable properties include: • Keypad Backlight—Set the light level (brightness) of the keypad backlight. Choose a percentage from 0 (Off) to 100 (full brightness). • Sleep Mode—Set how long the remote stays awake after no activity. The default setting is 15 seconds, but can be extended up to 60 seconds or can be reduced down to 0 to conserve battery life. • Battery Level—Displays current strength of batteries. • Channel —Displays the ZigBee channel (1-14) set for the RC100, which should match the ZigBee channel set for the controller. • Gateway—Displays the MAC address of the zigbee server (usually your controller unless you specify differently). • MAC—Displays the remote’s own MAC address. • Firmware Version—Displays the current firmware version. 7 Change Remote Control settings as needed at the RC100 remote itself by using the applicable button-press sequence: a. Change Backlight Level—To increase or decrease the backlight level: Press Room Off, 0, 0, 1 (in that order). After a single blink of Room Off, use the up or down arrow to set the level, then press Room Off to exit Edit mode and save the setting. b. Check ZigBee Channel—To determine the current ZigBee channel: Press Room Off, 0, 0, 3 (or Room Off, 7, 4, 7) (in that order) then count the blinks of Room Off. The number of blinks corresponds with the channel number. c. Change ZigBee Channel—To change the ZigBee channel in order to match the controller’s channel (which is sometimes changed to improve reception): Press Room Off, 0, 0, 2 (in that order). After a double blink of Room Off, key in the new ZigBee channel on the keypad (supported channels are 01 - 14), then press Room Off to exit Edit mode and save the setting. d. Reset to Factory Defaults—To reset all settings to the factory defaults (including ZigBee channel default of Channel 14): Press Room Off, 9, 9, 9. Program the Programmable Buttons On the Remote Control Version RC100, you can program 6 soft buttons (Red, Green, Yellow, Blue, *, and #) to perform programmed activities. These buttons can be programmed to execute any of the AV device’s macros or IR codes. Program these options using the AV device property page. 1 Start Composer and connect to a Director. 2 Ensure the System Design view is selected. 3 Ensure that you have the following devices in your project: • Controller • Remote Control RC100 • An AV device to be controlled 4 Select Connections view. 5 On the Network tab, ensure the controller and the Remote Control are both network identified (have a network address). 6 Program the programmable buttons (Red, Green, Yellow, Blue, *, or #) either based on the selected AV device or the selected room. Based on AV Device (pictured): a. Select System Design view. b. Select an AV device to display the device’s Properties page. c. On the device’s Properties page, choose Code or Macro for the button you want to program, then choose a code or macro from the drop-down list, edit Help text as needed, and then choose Set. Note: Help text describes custom programming to end-users under the House option in any of the system navigation devices. For example: (1) In System Design view, select Disc Changer. (2) Under Red button, choose Code. (3) From the drop-down list, choose Subtitle. (4) Choose the Set button to create a Subtitle button. Based on Room (not pictured): a. Select Programming view. b. Select a room in the Device Events pane. c. Select the Commands radio button in the [Room] Events pane. d. Use the drop-down menu to select a command or button (such as “Blue Button”). e. Build the script using items from the Action pane to program the actions desired in the room selected when the selected command or button is used. For more on programming, refer to the Composer Help file. Regulatory Compliance FCC FCC ID: R33C4SR150Z This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interf...