Login:
Votes - 2, Average rating: 4 ( )

User manual Wayne, model 3018DLX

Manafacture: Wayne
File size: 1.07 mb
File name:
Language of manual:en
Free link for this manual available at the bottom of the page



manual abstract


IMPORTANT: You MUST change the Transmitter security code prior to programming the device to the power head unit. WARNING: During programming the garage door may operate. Keep people and objects clear of the moving door to prevent door damage or possible personal injury. Changing the Transmitter Code 1. Press and hold the button on the transmitter that you want to change (left button or right button). The GREEN LED (light) will flash once and then turn off. 2. Continue to hold the button until the GREEN LED begins to flash (approx. 10 seconds). 3. When the GREEN LED flashes, immediately release the button and then immediately press and hold the same button again. The GREEN LED will now come on steady. 4. Continue to hold the button until the GREEN LED begins to flash (approx. 5 seconds). 5. When the GREEN LED flashes, immediately release the button. 6. The code for this button has now been changed to a new randomly generated code. Do not press the button again until instructed in “Programming Transmitter to Motor Head Power Unit”. 7. You must now re-program this transmitter to the motor head unit. See “Programming Transmitter to Motor Head Unit” above. Note: After the transmitter is programmed, see “Programming Transmitter to Power Head Unit” above. After completing “Programming Transmitter to Power Head Unit” proceed to step 24. 22 Step 24: Connecting Cushion Arm to Trolley Activate opener to bring trolley to factory pre-set close limit (See illustration). Cushion arm assembly consists of the door arm tube section and door arm rod, which are packed separately. To assemble, screw the door arm rod into the door arm tube in a clockwise direction approximately ten turns. Connect cushion arm assembly into trolley with open end of rod hook facing motor. Attach warning tag and red pull knob to red release cord connected to trolley. Step 25: Setting Trolley Close Position Activate opener to confirm trolley close position is 9” to 10” between the inside face of the door and the solid cushion arm rod. If adjustment of the trolley position is necessary, use the CLOSE TRAVEL ADJUSTMENT knob located on the bottom of the motor power head unit. A 1/4 turn equals approximately 1” of trolley movement; turn clockwise to move forward; counterclockwise to move back. 23 Step 26: Connecting Door Arm to Door Door Mounted Bracket Visually align cushion arm connecting hole with middle hole of door bracket by rotating tube section in appropriate direction. Release trolley (cushion arm attached) with manual release cord and pull trolley a few inches toward motor. Now rotate cushion arm tube section 2 turns counterclockwise to provide a cushion when door is closed or encounters an obstruction. Align connecting hole in Step 26: Connecting Door Arm to Door Door Mounted Bracket Visually align cushion arm connecting hole with middle hole of door bracket by rotating tube section in appropriate direction. Release trolley (cushion arm attached) with manual release cord and pull trolley a few inches toward motor. Now rotate cushion arm tube section 2 turns counterclockwise to provide a cushion when door is closed or encounters an obstruction. Align connecting hole in cushion arm to middle hole in door bracket; insert 3/8” dia. bolt and tighten locking nut, allowing for free pivoting of arm. Note: Do not over tighten locking nut, as this will cause binding between cushion arm and door bracket. WARNING: Failure to secure door arm to door bracket with locking nut can cause door arm to become disengaged from the trolley and fall, resulting in possible damage or personal injury. Step 27: Setting Door Close Travel Plus “Contact Obstruction Sensing” Test With wall control up/down button, activate door to full open position; reactivate to close position. The door should stop on the floor with the cushion arm and the bottom door seal slightly compressed. If the door reverses off the floor, turn close travel knob 1/4 turn “less”. If door is not completely closed, turn travel knob 1/4 turn “more”. Repeat if necessary. IMPORTANT! Test “Contact Obstruction Sensing Feature” IMPORTANT: After installing opener, the door must reverse when it contacts a 1 inch high object on the floor. Activate the door to the full, open position and place a 1” (25mm) solid test obstacle on the floor under the garage door. Activate the door to the closed position. The door should reverse upon contact with the 1” obstacle. If door stops on the 1” obstacle, adjust the close travel knob 1/4 turn “more” until door reverses upon contact with obstacle. Repeat if necessary. When the door reverses, remove the test object and run the full cycle of open and close of the door. Door should not reverse when it comes to the fully closed position. Note: If opener fails to pass this test, repeat Step 27. Also see Adjustment #2, page 28, (Contact Obstruction Sensing Adjustment). 24 Step 28: Setting Door Opening Travel Do not use adjustments to compensate for a poorly balanced door. This will i...

Other models in this manual:
Safety Gate - 3014 (1.07 mb)
Safety Gate - 3018 (1.07 mb)
Safety Gate - 3514 (1.07 mb)

Reviews



Your review
Your name:
Please, enter two numbers from picture:
capcha





Category