Votes - , Average rating:
(
)
)
Manafacture: SkyLink
File size: 62.3 kb
File name: remotes-G6VR.pdf
Language of manual:
The document is loading, please wait
 |
The document is loading, please wait
manual abstract
3. Connect the 2 wires from the existing wall button to the GTR Smart ButtonTM. Twist the 2 wires together with the wire connector provided. Polarity does not matter, so simply pick one wire from the existing wall button, and connect it to one of the wires on the Smart ButtonTM. Do the same for the 2nd wire. 4. After connecting the wires, mount the Smart ButtonTM on to the wall with 2 screws. 5. Plug in the AC cord of the garage door opener. The red light on the Smart ButtonTM should flash 15 seconds after plugging in the power. The red light will not flash immediately after plugging in the power, which is normal. The Smart ButtonTM is now ready to be operated. Note: Straighten up the antenna to improve signal reception. Remove existing wires Mounting Accessories 2. INSTALLATION (CONT) Smart ButtonTM 2) Multi-Function Wall Console Multi-Function Wall Console normally comes with 3 buttons that can be used to: 1) operate the garage door opener lighting, 2) lock the receiver so it doesn’t accept remote control operation, and 3) push button for door opening / closing Congratulations on your purchase of the Skylink® G6VR Universal Garage Door Remote Control. This is a kit with a universal remote control and Smart ButtonTM. It is 100% compatible with all garage door openers. Simply replace the traditional wall button by the Smart ButtonTM, that’s all for the installation. In this kit, you will find the following: Rating of the transformer: 12V DC, 100mA Diameter of DC plug : 3.5mm Note: Straighten up the antenna to improve signal reception. Universal Remote Control (Battery included) If you have the multi-function wall console, do not replace the wall console by the Smart ButtonTM. You need to install the Smart ButtonTM in parallel with your existing wall console. 1. Remove the existing wall console from the wall by removing the screws. 2. Remove the 2 screws that secure the wires on the wall console. 3. Connect the wires from the Smart ButtonTM to the existing wall console. Polarity does not matter, so simply pick one wire from the Smart ButtonTM, and connect it to one of the terminals on the existing wall console. Do the same for the 2nd wire. 4. After connecting the wires, mount the Smart ButtonTM on to the wall with 2 screws. Also mount the original wall console on to the wall. 5. Plug in the AC cord of the garage door opener. The red light on the Smart ButtonTM should flash 15 seconds after plugging in the power. The red light will not flash immediately after plugging in the power, which is normal. The Smart ButtonTM is now ready to be operated. 6. If the Smart ButtonTM red light does not flash at all 2 minutes after plugging in the AC cord, your garage door opener is probably too old. However, the Smart ButtonTM will still work by plugging in an adapter (purchase separately). Please contact Skylink® to purchase the adapter. If the red light on the Smart ButtonTM is flashing slowly, that indicates it is in standby mode. When a valid remote control signal is received, it will open / close the garage door. Simply press the button on the remote control or Smart ButtonTM, it will open / close the garage door. OPEN / CLOSE Programming Learn additional remote controls Smart ButtonTM can learn up to 15 remote controls. To learn additional remote controls, follow the instructions below: 1. Press the learn button on the side of the GTR. 2. Once the learn button is pressed, the LED will flash quickly. You may release the learn button. 3. Press the button on the remote control you would like to program. 4. Once the remote control is programmed, the LED will flash slowly, in the same way as it flashes in standby mode. 5. You may now operate the garage door opener with this new remote control. Learn Button 3. OPERATION Antenna 2 Wire Connectors Visor clip 3. OPERATION (CONT) 3. OPERATION (CONT) Erase remote controls To erase unwanted remote control(s), first erase all remote controls, then learn the ones you would like to keep. To erase remote control(s) 1. Press and hold the learn button for approx 10 seconds. 2. The LED will flash rapidly after 10 seconds to indicate all the programmed remote controls have been erased. You may now release the learn button. 3. You have erased all the remote controls in the Smart ButtonTM. 4. BATTERY 12 volt alkaline battery (size 23A) included. 5. ADDITIONAL TRANSMITTER You can add up to 15 additional transmitters to control the same receiver. Skylink® offers Keychain Transmitters and Keypad Transmitters to work with your receiver. For more information, please visit our website at or contact us. 6. WARNING DO NOT let children use the garage door transmitter without adult supervision. Children can injure themselves or others by the garage door. 7. FCC The Garage Door Remote Control is approved by the FCC and it complies with Part 15 of the FCC Rules. Its operation is subject to the following two conditions : 1. This device may not cause harmful interference. 2. This d...