Votes - 3, Average rating: 3.7
(
)
)
|
manual abstract
Note: The length of the red/black wire is 20ft, so the receiver must be plugged into an electrical outlet that is within 20ft of the wall mounted door control. If there is no electrical outlet within 20ft of the wall mounted door control, an extension cord can be used for temporary installation. 2. INSTALLATION (CONT) 2 3 3. TROUBLE SHOOTING Q: Door opener does not react after pressing the button on the transmitter. A:- Ensure you hear 3 beeps from the keypad transmitter after entering the default PIN and [#]. If you do not hear 3 beeps, that means the PIN you entered is incorrect. Re-enter the correct PIN. - If the red light on the receiver flashes after entering the PIN on the transmitter, but the door opener does not respond, please ensure the red/black wire is successfully connected from the receiver to the wall mounted door control. - Ensure the wires that are previously connected to the wall mounted door control are not loose. - Ensure the code setting on the keypad transmitter is the same as the receiver. Refer to section 4 to check the code setting. RED/BLACK WIRE RECEIVER Existing wires connected to garage door opener. (Do not remove) 1 Remove the wall-mounted door control from the wall by removing the screws. Connect the stripped ends of the Red/Black wire to the 2 terminals (2 screws) on the back of the wall mounted door control. (Polarity does not matter.) Unplug the power cord of your garage door opener before installation to ensure power is not connected. Wall Mounted Door Control Electrical Outlet WARNING Remove power cord of garage door opener before installation. Red / Black wire Note: There should be another pair of wires connected to the 2 terminals already. Do not remove/ disconnect these existing wires. Note: If you see no screws mounting the wall mounted door control, the screws are probably under-neath the front cover. Remove the front cover by pressing onto the tabs on top of the cover. Remove front cover first Existing wires Different wall-mounted door controls Note: Alternative wiring options are available, the receiver can be connected directly to the opener’s motor. Please contact customer service for further information regarding alternative wiring options. Garage Door Receiver Clip 4. CHANGE THE OPERATION CODE FOR BOTH TRANSMITTER AND RECEIVER (BOTH) 4. CHANGE THE OPERATION CODE FOR BOTH TRANSMITTER AND RECEIVER (BOTH) 6. CHANGE PIN 2 You can randomly remove some connectors, leaving some in place. A connector can be removed with the clip, as shown. 3 4 If the connector is placed on the top and middle posts, that column is set on “ + ” . If the connector is placed on the middle and bottom posts, that column is set on “ - ”. If the connector is removed completely, (not placed on any posts), it is set to “ 0 ”. (see diagram for examples of how to set a column to the three different positions). When removing a connector to set a column to “ 0 ”, ‘+’ save the connector in case you change the code at a later date. ‘-’ ‘0’ After setting up the code connectors on the keypad transmitter, you are ready to set the same code on the receiver. Remove the receiver from the electrical outlet before WARNING changing the code. 5 Remove the screw that holds the connector cover, and remove the cover. 6 You will see 10 connectors. The settings must match with those of the transmitter. Connectors 1 to 10 are the same. 97 Put the cover and screw back onto the receiver. Plug the receiver into an electrical outlet. 8 Enter [0,0,0,0] [#] will open the garage door. You can now mount the transmitter on a desired location. Lift up the cover and insert screw above the keypad in the slot provided (a). Remove the battery cover and insert the second screw in the lower slot (b). Tighten all screws. Replace the battery cover, insert and tighten screw (c). (a) (c) (b) 5. KEYPAD OPERATION NOTE: The backlight comes on and a beep is emitted when any key is pressed. The backlight of the keypad may not be visible when it is too bright outside. When any key is pressed, the next key must be pressed within 5 seconds or the backlight turns off and the sequence is cancelled. You must begin again. If the keypad does not emit a beep when pressed, wait a few seconds and press the key again. Follow the instructions below to change the PIN. To change your PIN: 1. Enter the current PIN, (factory default PIN 0 0 0 0), press * , 2. Enter new 4 digit PIN, press , * 3. Enter new PIN again, press . * For example, if you are changing the PIN number from 0000 to 1234, enter the following sequence, 0000, ,1234, ,1234, . *** If confirmed, the backlit LED flashes and the unit emits a long beep. If you do not hear 3 beeps after the 4-digit PIN and [#] is entered, that means you have entered an incorrect PIN, and the keypad transmitter will not operate your garage door. 7. BATTERY Two 3 volt Lithium type (CR2032) batteries (included). It is time to change the batteries when the backlight no longer appears. + - Battery Compartment 8. ADDITIO...