In this package, you will find the following: Crimper Garage Door Transmitter MK-318 (Battery inside) Unplug the power cord of your garage door opener before installation to ensure power is not connected. DO NOT let children use the gargae door Transmitter without adult supervision. Children can injure themselves or others by the garage door. WARNING DO NOT use remote to control the door without safety beams. 1. Open up the “Easy ClipTM” and place it underneath the existing 2 wires of the wall button / wall console. 2. Ensure a pair of the wall button ribbon wires are placed properly inside the channels of the “Easy ClipTM”. NOTE: Ensure the ribbon wires are not twisted but laid flat inside the clip. If your wall button ribbon wires are not the same kind as shown in the diagram, please refer below (4) or visit our website or contact us for more information. Easy ClipTM Ribbon Wires Wall Button Ribbon Wires Press / lock 3. Press and lock the clip by snapping it together. The included Crimper helps you lock the “Easy ClipTM”. Close the cover and press down to lock the cover using this Crimper until you hear a “click”. 4. If the Easy ClipTM” cannot clip the wires from your wall button, cut off the Easy ClipTM” then connect two wires from the Smart ButtonTM GB-318 to the wall button. a) Disconnect the existing wall button from the wall. b) Connect the 2 wires from the Smart ButtonTM GB-318 to your existing wall button. Polarity does not matter, so simply pick one wire from the Smart ButtonTM GB-318 and connect it to one of the screw terminals on your wall button. Connect the 2nd wire to the other screw terminal. c) Reconnect the wall button back. Rating of the transformer: 12V DC, 100mA Diameter of DC plug : 3.5mm 7. Secure the SmartButtonTM GB-318 properly with the mounting accessories. Note: Do not cut the antenna! Straighten up the antenna to improve signal reception. 5. If the wall button wires are hidden inside the wall, please connect the “Easy ClipTM” to the exposed wires attached to the terminals of the garage door opener. You need to do the programming in order to add the transmitter to a receiver. 3. PROGRAM TRANSMITTER MK-318 TO RECEIVER GB-318 Smart ButtonTM GB-318 can learn up to sixteen single button transmitters or keypads or five 3-button transmitter . To add remote controls, follow the instructions below: 1. Press the learn button on the side of the Smart ButtonTM GB-318. 2. Once the learn button is pressed, the LED will flash quickly. Release the learn button. 3. Within 30 seconds, press any one of the 3 buttons on the transmitter that you want to program to the receiver. 4. Once the remote control is programmed, the LED will flash slowly, in the same way as it flashes in standby mode. 5. You may now operate the garage door opener with this new remote control. 6. To program this transmitter to control another receiver, repeat process (1) to (4) to program another button on the remote control. If the red LED flashes slowly, the Smart ButtonTM GB-318 is in standby mode. When a valid remote control signal is received, it will open / close the garage door. Press the programmed button on the remote control or Smart ButtonTM GB-318, it will open / close the garage door. OPEN / CLOSE Button 4. OPERATION Double Sided Tape 2. RECEIVER INSTALLATION Note: After installation of the “Easy Clip TM ”, if you want to re-install the Smart Button TM GB-318 to another place, please open the “Easy Clip TM ” by gently unlocking the two buckles with a screw driver, and remove it from the wires. Do not re-use the “Easy Clip TM ”, refer to Step 4 to re-install it. LED Garage Door Receiver Smart ButtonTM GB-318 Connect the receiver - Smart ButtonTM GB-318 to your current garage door opener system, you can use the transmitter - remote MK-318 to open or close the garage door. To erase unwanted remote control(s)from the memory of Smart ButtonTM GB-318, first erase all remote controls, then learn the one(s) you would like to keep, follow the steps below: 1. Press and hold the learn button for approximately 10 seconds. 2. The LED will flash rapidly after 10 seconds to indicate all the programmed remote controls have been erased. You may now release the learn button. 3. You have erased all the remote controls programmed to the Smart ButtonTM GB-318. 5. ERASE TRANSMITTERS 6. TROUBLE SHOOTING Q: What can I do if the door opener does not react after I press the button on the transmitter ? A: - Ensure when the button on the transmitter is pressed, the red LED on the transmitter comes on. Otherwise, check if the battery is inserted properly. - Make sure the correct button on the transmitter is pressed. - Ensure the wires that were previously connected to the wall mounted door control are not loose. - Ensure the transmitter has been programmed to the receiver. Refer to section 2 for how to program a transmitter to the receiver. 6. Power up the garage door opener, the red LED on the Smart ButtonTM GB-318 should...