4 Press the navigation buttons to select an option, then press 5 Press to exit. Select language 1 Press MENU. 2 Press the navigation buttons to select [SETTINGS], then press 3 Press the navigation buttons to select [LANGUAGE] , then press . » The following options are displayed: 26 EN ........ Espanol Portugues Pyccknn ........ Espanol Portugues Pyccknn [OSD Lang] [Audio Lang] [Subtitle lang] [Menu lang] [DivX [R] VOD] 4 Press the navigation buttons to select an item, then press 5 Pre

insert mast through U-bolt.Tighten nuts securely (fig.5) (Mast sold separately). 6. Connect 2 mast sections as shown in figure 6 (included in SDV9201K only) ENAiming the Antenna 7. Connect a good quality RG-6 coaxial cable to the transformer. Slide the weatherproof boot over the connection firmly until it seals (fig.7) (Cable sold separately) fig. 7 fig. 8 8. Attach cable standoff to mast as shown in figure 8 (included in SDV9201K only) Aiming the Antenna Before permanently mounting the antenna

14 EN 1 Press MENU repeatedly until [LOCAL] is displayed. 2 Rotate to select a setting: [LOCAL ON] (local on): only stations with strong signal can be broadcast. [LOCAL OFF] (local off): stations with strong and weak signals can be broadcast. Store radio stations in memory You can store up to 6 stations in each band. Store stations automatically 1 In Radio mode, press and hold DBB until [STORE - - -] is displayed. 2 Press » The six strongest stations of the selected band are saved in preset

••Make sure that all loose leads are insulated with electrical tape. ••Make sure that the leads do not get caught under screws iron parts that will move (e.g. seat rail). ••Make sure that all ground (earth) leads are run to a common ground (earth) point. ••Use only the supplied mounting hardware for a safe and secure installation. ••Improper fuses can cause damage or fire. When you need to change the fuse, consult a professional. ••When you connect other devices to this system, make sure that th

FOR YOUR SAFETY, KEEP LADDER AND ANTENNA AWAY FROM POWER LINES. CONTACT MAY CAUSE ELECTROCUTION Antenna Grounding and Safety Warning 1. Outdoor antennas and lead-in conductors from antenna to a building, should not cross over open conductors of electric light of power circuits.They should be kept away from all circuits to avoid the possibility of accidental contact. 2. Each conductor of a lead-in from an outdoor antenna should be connected with an antenna discharge unit. Antenna discharge units

Introduction With the in-car audio system, you can enjoy your drive while you listen to: • FM or AM (MW) radio • Audio from CD or MP3 disc • Audio from a USB drive • Audio from external devices What’s in the box Check and identify the contents of your package: a In-car audio system b Remote control c Rubber cushion d Screw (4 pieces) e Disassembly tool ( 2 pieces) f Front panel g Trim plate h Carrying case for front panel i User manual j Quick start guide k Standard connector EN 7 e MENU / DISP

If damage is caused by failure to follow instructions, the warranty does not apply. in hazardous radiation of EMC or other unsafe operation. . The device is designed for negative ground (ear th) 12 V DC operation only. . To ensure safe driving, adjust the volume to a safe and comfor table level. . Improper fuses can cause damage or consult a professional. . Use only the supplied mounting hardware for a safe and secure installation. . To avoid shor t circuits, do not expose the device to

1 Press to release the front panel. 2 Pull the front panel leftward to release it from the chassis of the main unit. 3 Pull the front panel outwards to remove it. Install remote control battery Caution ••Risk of explosion! Keep batteries away from heat, sunshine or fire. Never discard batteries in fire. ••Risk of decreased battery life! Never mix different brands or types of batteries. ••Risk of product damage! When the remote control is not used for long periods, remove the batteries. ••Perchlo