Votes - 0, Average rating: 0
(
)
)
|
manual abstract
E
E
N
N
Installation Guide
G
G
L
L
I
I
S
S
H
❐ Identify All Leads
If your car is not wired for an audio unit:
H
Go to the fuse block and find the fuse port for the
13
The first step in installation is to identify all the car
14
WARNING
battery, usually marked BAT.
wires you’ll use when hooking up your sound sys-
This installation information is designed for experienced installers and is not in-
tem.
Speakers
Identify the car speaker leads. There are two leads
tended for non-technical individuals. It does not contain warnings or cautions of po-
As you identify each wire, we suggest that you label
for each speaker which are usually color coded.
tential dangers involved in attempting to install this product.
it using masking tape and a permanent marker.
This will help avoid confusion when making con-
A handy way to identify the speaker leads and the
speaker they are connected with is to test the leads
Any attempt to install this product in a motor car by anyone other than qualified in-
nections later.
using a 1.5 V AA battery as follows.
staller could cause damage to the electrical system and could result in serious per-
Note:
Hold one lead against one pole of the battery and
sonal injury or death.
≥ Do not connect the power connector to the stereo
stroke the other lead across the other pole. You will
unit until you have made all connections. If there
hear a scraping sound in one of the speakers if you
are no plastic caps on the stereo hooking wires,
are holding a speaker lead.
❐ Installation Hardware
If you encounter problems, please consult your
insulate all exposed leads with electrical tape until
If not, keep testing different lead combinations until
nearest professional installer.
you are ready to use them. Identify the leads in
you have located all the speaker leads. When you
No.
Item
Diagram
Q’ty
the following order.
label them, include the speaker location for each.
Caution:
1
Mounting collar
1
Power Lead
≥ This unit operates with a 12 V DC negative
Antenna Motor
If your car has a radio or is pre-wired for one:
ground auto battery system only. Do not at-
If your car is equipped with an automatic power an-
Cut the connector wires one at a time from the plug
2
Hex. nut (5 mm
tenna, identify the car motor antenna lead by con-
·)
1
tempt to use it in any other system. Doing so
(leaving the leads as long as possible) so that you
could cause serious damage.
necting one bulb tester lead to the car battery lead
can work with individual leads.
and touching the remaining exposed wires from the
3
Rear support strap
1
Before you begin installation, look for the items
cut radio connector plug one at a time. You will
which are packed with your unit.
hear the antenna motor activate when you touch
4
the correct wire.
Tapping screw
1
≥ Warranty Card…Fill this out promptly.
(5 mm·a16 mm)
≥ Panasonic Servicenter List for Service Directory
Antenna
The antenna lead is a thick, black wire with a metal
5
Mounting bolt (5 mm
…Keep for future reference in case the product
·)
1
Turn the ignition on to the accessory position, and
needs servicing.
plug at the end.
ground one lead of the test bulb to the chassis.
≥ Installation Hardware…Needed for in-dash in-
6
Power connector
1
stallation.
Touch the other lead of the test bulb to each of the
❐ Connect All Leads
❐ Required Tools
exposed wires from the cut radio connector plug.
Now that you have identified all the wires in the car,
7
Removable face plate
1
Touch one wire at a time until you find the outlet
you are ready to begin connecting them to the
case
You’ll need a screwdriver, a 1.5 V AA battery, and
that causes the test bulb to light.
stereo unit wires. The wiring diagram (➡ page 28)
the following:
shows the proper connections and color coding of
8
Now turn the ignition off and then on. If the bulb
Trim plate
1
12 V DC
Electrical
Side-cut
also turns off and on, that outlet is the car power
the leads.
Test bulb
tape
pliers
lead.
We strongly recommend that you test the unit be-
❐ Overview
fore making a final installation.
If your car is not wired for an audio unit:
You can set the unit on the floor and make tempo-
Go to the fuse block and find the fuse port for radio
This product should be installed by a professional.
rary connections to test the unit. Use electrical tape
(RADIO), accessory (ACC), or ignition (IGN).
However, if you plan to install this product yourself,
to cover all exposed wires.
your first step is to decide where to install it. The
Battery Lead
instructions in these pages will guide you through
❐ Dashboard Specifications
If your stereo unit has a yellow lead, you will need
Important:
the remaining steps:
to locate the car’s battery lead. Otherwise you may
Thickness Min. 3⁄
≥ Connect the red power lead last, after you
16z (4.75 mm)
(Please refer to the “WARNING” statement
ignore this procedure. (The yellow battery lead pro-
have made and insulated all other connec-
Max. 7⁄32z (5.56 mm)
above.)
vides continuous power to maintain a clock, memo-
tions.
ry storage, or other function.)
≥ Identify and label the car wires.
23⁄
Ground
32z (53 mm)
≥ Connect the car wires to the wires of the power
If your car has a radio or is pre-wired for one:
Connect the black ground lead of the power con-
connector.
With the ignition and headlights off, identify the car
nector to the metal car chassis.
≥ Install the unit in the dashboard.
75⁄
battery lead by grounding one lead of the test bulb
32z (182 mm)
≥ Check the operation of the unit.
to the chassis and checking the remaining exposed
wires from the cut radio connector plug.
22
23
CQ-DPX152/DP102U
CQ-DPX152/DP102U
...Other models in this manual:
Car Receivers - CQDPX152U (327.15 kb)