Votes - 4, Average rating: 3.5
(
)
)
|
manual abstract
You can select: AUTO: the TV system is auto switched according to the disc system. NTSC: this system is used in USA, Taiwan, Japan etc. PAL: this system is used in China, Europe, Hong Kong etc. • TV type 4:3 PS: When the unit connects to the normal TV set, the wide-screen image shows on the full screen, but some part is cut off. 4:3 LB: When the unit connects to the normal TV set, the wide-screen image shows and black bars appear on the top and bottom of screen. 16:9: Use this item when the unit is connected with the wide screen TV set. • Password Here you can change the password. Insert your old password or 0000 (the general one). Insert the new password. Insert it again. Press OK button to save the new password. • Rating The rating level is for parents to control playing content and protect your children from violence and erotic. The disc, the level of which is higher than the setting level cannot be played. To change the parental control level you should enter the password (your or the general one: 0000). • Default Reset to the initial factory setups 28 Language setup • OSD language Select the OSD language. • Audio language Select the audio language (if DVD disc supports several audio l anguages). • Subtitle language Select the subtitle language (if DVD disc supports several subtitle l anguages). • Menu language Select the DISC menu language (if DVD disc supports several menu languages). Audio setup • Audio out SPDIF/Off: no digital signal out (optical or coaxial output off), only analog audio output. • Key Setup basic music tone. Video setup • Brightness, Contrast, Hue, Saturation, Sharpness You can set the Brightness, Contrast, Hue, Saturation, Sharpness according to your preference. 29 Speaker setup LT/RT: The audio out is Left and Right channels format even if the original sound is 5.1CH format. Stereo: The audio out format is stereo even if the original sound is 5.1CH format. VSS: The audio format Advanced Virtual Surround Sound Digital setup • OP MODE Select the output mode: Line out, RF remod. • DYNAMIC RANGE If watching large dynamic scope movie program at night, to select this mode you can reduce the volume to a very low level, at the same time, to keep the fine details sounds. In this case, this doesn't disturb the family and keep the quality sounds. • DUAL MONO Stereo: stereo output signal. Mono L: left output signal. Mono R: right output signal. Mix Mono: left and right output average signal. 30 TV Operation 1. To switch on a suited video color system and a suited TV accompanying sound system In TV mode, short press the BAND button repeatedly to switch on a suited video color system of the 5 ones of the unit: PAL, SECAM, PAL M, PAL N, NTSC. If your monitor has only NTSC or PAL system, the monitor screen will blink or become colorless when a not suited video color system of the unit is switched on. In one of the above 5 video color systems, long press the BAND button repeatedly to switch on a suited TV accompanying sound system of the unit for the selected video color system: PAL(PAL-DK, PAL-BG, PAL-I); SECAM(SECAM-BG, SECAM-DK); PAL M (PAL M); PAL N(PAL N); NTSC(NTSC MN). If you switch on a not suited TV accompanying sound system of the unit for the monitor, it cannot output sound. 2. To search and save (a) TV station(s) In TV mode, short press the APS button, it will search a available TV station from the current frequency to the high frequency. After searched a available TV station, it will stop searching and output the signal of the available TV station and the available TV station will be saved in the channel. In TV mode, long press the APS button, it will search all available TV stations from the lowest frequency to the highest frequency. After searched for a circle, it will stop searching and output the signal of the available TV station with the lowest frequency and all the available TV stations from the lowest frequency to the highest frequency will be saved in the channels from 1 to 95. 3. To select a desired channel with an available TV station with UP/DN or »i/l« buttons on the remote controller. In TV mode, short press the UP/DN button on the front panel or the »i/l«button on the remote controller to select all TV channels. After Long pressing the APS button to search for a circle, short press the UP/DN button on the front panel or the »i/i« button on the remote controller to select the desired channels with available TV stations. 4. To select a desired channel with the number buttons In TV mode, press one of the 10 buttons (1-10) to directly select the channel. In TV mode, to directly select a channel more than 10, firstly press the 10+ button to display_, then input the digit in tens place and then input the digit in units place with the 10 buttons (1-10). 5. To fine the TV signal In TV mode, press and hold the UP/DN button on the front panel or the »i/l« button on the remote controller to fine the TV signal of the cur...
Other models in this manual:Portable Players - SM-CMD3006 (2.3 mb)