Votes - 5, Average rating: 3.4
(
)
)
|
Photos and specs Pioneer DEH-3000MP |
Other manuals for this model:
manual abstract
To protect the wiring, wrap adhesive tape around them where they lie against metal parts. — Place all cables away from moving parts, such as gearshift and seat rails. — Place all cables away from hot places, such as near the heater outlet. — Do not pass the yellow cable through a hole into the engine compartment to connect to a battery. — Cover any disconnected cable connectors with insulating tape. — Do not shorten any cables. — Never cut the insulation of the power cable of this unit in orderto share the power with other devices. Current capacity of the cable is limited. — Use a fuse of the rating prescribed. — Never wire the speaker negative cable directly to ground. — Never band together multiple speaker's negative cables. • Control signal is output through blue/white cable when this unit is powered on. Connect it to an external power amp's system remote control orthe vehicle's auto-antenna relay control terminal (max. 300 mA 12 V DC). If the vehicle is equipped with a glass antenna, connect it to the antenna booster power supply terminal. • Never connect blue/white cable to external power amp's powerterminal. Also, never connect it to the powerterminal of the auto antenna. Otherwise, battery drain or malfunction may result. • Black cable is ground. This cable and other product's ground cable (especially, high-cur-rent products such as power amp) must be wired separately. Otherwise, fire or malfunction may result if they are accidentally detached. Connection Diagram (Fig. 1) 1 This product 2 Rear output 3 Antenna jack 4 Fuse (10 A) 5 Note: Depending on the kind of vehicle, the function of 3* and 5* may be different. In this case, be sure to connect 2* to 5* and 4* to 3*. 6 Connect leads of the same color to each other. 7 Cap (1 *) Do not remove cap if this terminal is not in use. 8 Yellow (3*) Back-up (or accessory) 9 Yellow (2*) Connect to the constant 12 V supply terminal. 10 Red (5*) Accessory (or back-up) 11 Red (4*) Connect to terminal controlled by ignition switch (12 V DC). 12 Black (chassis ground) Connect to a clean, paint-free metal location. En (Connections j 13 ISO connector In some vehicles, the ISO connector may be divided into two. In this case, be sure to connect to both connectors. 14 Speaker leads White: Front left © White/black: Front left © Gray: Front right © Gray/black: Front right © Green: Rear left © Green/black: Rear left © Violet: Rear right © Violet/black: Rear right© 15 Wired remote input Hard-wired remote control adaptor can be connected (sold separately). 16 Connect with RCA cables (sold separately) 17 Power amp (sold separately) 18 Yellow/black If you use an equipment with Mute function, wire this lead to the Audio Mute lead on that equipment. If not, keep the Audio Mute lead free of any connections. 19 Blue/white Connect to system control terminal of the power amp (max. 300 mA 12 V DC). 20 System remote control 21 Blue/white (7*) Connect to auto-antenna relay control terminal (max. 300 mA 12 V DC). 22 Blue/white (6*) The pin position of the ISO connector will differ depends on the type of vehicle. Connect 6* and 7* when Pin 5 is an antenna control type. In anothertype of vehicle, never connect 6* and 7*. 23 Left 24 Right 25 Rear speaker 26 Perform these connections when using the optional amplifier.S En (Conexiones ) ( j Importante • Cuando esta unidad se instala en un vehículo sin posición ACC (accesorio) en la llave de encendido, el cable rojo se debe conectar al terminal que pueda detectar la operación de la llave de encendido. De lo contrario, puede descargarse la batería. Posición ACC Sin posición ACC • El uso de esta unidad en unas condiciones distintas de las indicadas a continuación podría causar incendios o fallos de funcionamiento. — Vehículos con una batería de 12 voltios y conexión a tierra negativa. — Altavoces con 50 W (valor de salida) y 4 ohmios a 8 ohmios (valor de impedancia). • Para evitar cortocircuitos, sobrecalentamiento o fallos de funcionamiento, asegúrese de seguir las siguientes instrucciones. — Desconecte el terminal negativo de la batería antes de la instalación. — Asegure el cableado con pinzas para cables o cinta adhesiva. Para proteger el cableado, envuelva con cinta adhesiva las partes en donde esté en contacto con piezas metálicas. — Coloque todos los cables alejados de las partes móviles, como la palanca de cambios y los rieles de los asientos. — Coloque todos los cables alejados de lugares calientes, como cerca de la salida del calefactor. — No pase el cable amarillo a través de un orificio en el compartimiento del motor para conectarlo a la batería. — Cubra con cinta aislante los conectores de cables que queden desconectados. — No acorte ningún cable. — Nunca corte el aislamiento del cable de alimentación de esta unidad para compartir la corriente con otros equipos. La capacidad de corriente del cable es limitada. — Utilice un fusible con la tensión nominal...