Votes - 0, Average rating: 0
(
)
)
|
Other manuals for this model:
manual abstract
1 Press and hold SRC/OFF until the unit turns off. 2 Press M.C. and hold until the initial setting menu appears in the display. 3 Turn M.C. to select the initial setting. After selecting, perform the following procedures to set the initial setting. Language select (multi-language) For your convenience, this unit equips multiple language display. You can select the language best suited to your first language. 1 Press M.C. to select the language. English—Francais—Italiano—Espanol— Deutsch—Nederlands—РУССКИЙ Calendar (setting the date) 1 Push M.C. left or right to select the segment of the calendar display you wish to set. Year—Day—Month 2 Push M.C. up or down to set the date. Clock (setting the clock) 1 Push M.C. left or right to select the segment of the clock display you wish to set. Hour—Minute 2 Push M.C. up or down to put a clock right. ! You can match the clock to a time signal by pressing M.C. ! If 00 to 29, the minutes are rounded down. (e. g., 10:18 becomes 10:00.) ! If 30 to 59, the minutes are rounded up. (e.g., 10:36 becomes 11:00.) EngineTime alert (elapsed time display setting) This setting allows you to measure the length of time that elapses from when the machine is turned on and display the amount of elapsed time per set period. Also, you will hear alarm. 1 Press M.C. to select your favorite setting. OFF—15Minutes—30Minutes FM step (FM tuning step) Normally, the FM tuning step employed by seek tuning is 50 kHz. When AF or TA is on, the tuning step automatically changes to 100 kHz. It may be preferable to set the tuning step to 50 kHz when AF is on. 1 Press M.C. to select the FM tuning step. 50kHz (50 kHz)—100kHz (100 kHz) Auto PI (auto PI seek) The unit can automatically search for a different station with the same programming, even during preset recall. 1 Press M.C. to turn Auto PI seek on or off. USB plug&play (plug and play) This setting allows you to switch your source to USB/ iPod automatically. 1 Press M.C. to turn the plug and play function on or off. ! ON – When USB storage device/iPod is connected, the source is automatically switched to USB/iPod. If you disconnect your USB storage device/iPod, this unit’s source is turned off. ! OFF – When USB storage device/iPod is connected, the source does not switch to USB/ iPod automatically. Please manually change the source to USB/iPod. Warning tone (warning tone setting) If the front panel is not detached from the head unit within four seconds of turning off the ignition, a warning tone sounds. You can turn off the warning tone. 1 Press M.C. to turn the warning tone on or off. AUX (auxiliary input) Activate this setting when using an auxiliar y device connected to this unit. 1 Press M.C. to turn auxiliar y setting on or off. Dimmer (dimmer setting) To prevent the display from being too bright at night, the display is automatically dimmed when the car ’s headlights are turned on. You can turn the dimmer on or off. 1 Press M.C. to turn dimmer on or off. Brightness (display brightness setting) 16 En Section Operating this unit 02 1 Push M.C. left or right to adjust the brightness level. 0 to 15 is displayed as the level is increased or decreased. ! When dimmer is functioning, the brightness level can be adjusted 0 to 10. S/W control (rear output and subwoofer setting) This unit’s rear output (rear speaker leads output and RCA rear output) can be used for full-range speaker (Rear SP :F.Range) or subwoofer (Rear SP :S/W) connection. If you switch the rear output setting to Rear SP :S/W, you can connect a rear speaker lead directly to a subwoofer without using an auxiliar y amp. 1 Press M.C. to switch the rear output setting. ! When no subwoofer is connected to the rear output, select Rear SP :F.Range (full-range speaker). ! When a subwoofer is connected to the rear output, select Rear SP :S/W (subwoofer). ! Even if you change this setting, there will be no output unless you turn the subwoofer output on (refer to Sub W.1 (subwoofer on/off setting) on page 15). ! If you change this setting, subwoofer output in the audio menu will return to the factory settings. ! Both rear speaker lead outputs and RCA rear output are switched simultaneously in this setting. Mute (muting or attenuation setting) 1 Press M.C. to switch the telephone muting/attenuation. ! The sound is muted or attenuated, MUTE or ATT are displayed and no audio adjustment is possible. ! Sound from this system returns to normal when the muting or attenuation is canceled. Demonstration (demo display setting) 1 Press M.C. to turn the demo display on or off. ! You can also turn on or off feature demo by pressing DISP while this unit is turned off. For more details, refer to Demo mode on page 3. Reverse mode (reverse mode setting) 1 Press M.C. to turn the reverse mode on or off. ! You can also turn on or off reverse mode by pressing BAND while this unit is turned off. For more details, refer to Reverse mode on page 4. Ever-scroll (scroll mode setting) When ever scroll is set to ON, recorded ...