Votes - 2, Average rating: 4
(
)
)
|
manual abstract
Clockwise opens the squelch and counterclockwise tightens the squelch. © DX Press [DX] to turn the DX PacketClusters Monitor ON and OFF. © P.IN Press [P.IN] to enter PM Channel registration mode. © 0 Press W>] to turn the transceiver power ON and OFF. OPERATION PANEL (REAR & LEFT) © GPS Connect the GPS receiver or the Weather Station to this jack using the supplied cable with a 2.5 mm (1/10") 3-conductor plug. ® com This terminal is for connecting to a PC. Use a PG-5G (option) cable when connecting the built-in TNC to a computer D-SUB terminal. @ Panel jack Connect the TX/ RX unit to this jack using the supplied Modular plug cable. 11 DISPLAY < A Band > < B Band > 96 PACKET T" HhUITF;h L-'hR -0 FMFiM =F |BQ3 fiPRS|l sff I i £ : oo nm CTRL L'H + R IB * h HS9 □ QCT 144.006 KEVI f”oTe"reu 25 I B C Ü N GPS(3 DCS FM 36 430.006 " LOU PF1 »25 wx PF2 pmumute l'Nhir lco: Indicator Description 1 = i—I l"“l ■i. .i— ■ Clock display (Setting Time: Menu 525) nm Appears when there is a transmission band available. Blinks when the cross-band repeater is ON (K type only). i“" T D i ■— ■ ISI. Appears when there is an operation band available. Blinks when the wireless remote control is ON (K type only). Appears when the Tone function is ON. CT Appears when the CTCSS function is ON. EJCS Appears when the DCS function is ON. + Appears when the Shift function is set to plus. - Appears when the Shift function is set to minus. R Appears when the Reverse function is ON. ra LU Appears when the ASC function is ON. Blinks when the ASC function is performing an OK check. .-.LJ nil Appears while in AM mode. FM Appears while in FM mode. [£j Appears while in Narrow FM mode. D- Appears when the selected channel is non-registered while in Memory Input mode. № r Appears when the selected channel is registered while in Memory Input mode. 139 Displays the Memory channel number. A Appears when the Memory Channel Lockout function is ON. H Appears while using High output power. Blinks when the temperature protection circuit (transmit power save) turns on (K, E types only). 12 Indicator Description M Appears while using Middle output power. Blinks when the temperature protection circuit (transmit power save) turns on. L. Appears while using Low output power. 144.006, Displays the operating frequency. i~.i ¡^s/ U' !J _■ i Appears when receiving a busy signal. ............................Illllllllllllllllllll Performs as an S meter when receiving a signal and displays the selected power level while transmitting. 1. I11". i__i ! ■.! ¡»; j pi. Appears while transmitting. D Appears while using the External data band. □ Appears while using the Internal data band. Appears when the data terminal is set as 9600 bps. MUTE Appears when the mute function is ON. LlJ Appears while making a continuous recording. 14.11 1... ■4.11 Appears while in EchoLink Sysop mode. loci: Appears when the Key Lock function is ON. PMH Displays the PM channel number. wx Appears when Weather Alert is ON. Blinks when receiving a signal (K type only). a Appears when a message is received. upF:i Appears when the Beacon type is set to "APRS". mhUITRh Appears when the Beacon type is set to "NAVITRA". PACKET Appears while in PACKET mode. IS: Appears when the packet transfer rate is set to 1200 bps. 96 Appears when the packet transfer rate is set to 9600 bps. BCON Appears when the Beacon function is ON. GPS Appears when the GPS port input is set to "GPS". Blinks while positioning. WXI Appears when the GPS port input is set to Weather Station. L'H Appears when Voice Alert is set to "ON". L'flF: Appears when Voice Alert is set to "RX ONLY". 13 TX/ RX UNIT REAR PANEL © ANT Connect an M-type (TM-D710A) or N-type (TM-D710E) external antenna to this terminal. When making test transmissions, connect a dummy load in place of the antenna. The antenna system or load should have an impedance of 50 Q. ® DATA This is the data input/output terminal. Use a PG-5H (option) data communications cable when connecting to the PC voice input/output terminal. ® PC This terminal is for connecting to a PC. Use a PG-5G (option) cable or a PG-5H (option) serial communications cable when connecting to a computer D-SUB terminal. © SP (SP 1/ SP 2) If desired, connect 1 or 2 external speakers for clearer audio. These jacks accept 3.5 mm (1/8") diameter, 2-conductor plugs. TX/ RX UNIT SUB PANEL © □ □ MIC KENWOOD © MIC Connect the supplied microphone to this jack. @ PANEL Connect the Operation panel to this jack using the supplied Modular plug cable. 14 MICROPHONE (MC-59) Microphone Jack PTT © PTT switch Press and hold, then speak into the microphone to transmit. @ DTMF keypad Press these keys to make DTMF calls, enter frequencies, or enter characters. ® CALL/ A Functions the same as the transceiver front panel [CALL] key. This is also the PF4 key and can be reprogrammed with a programmable function. © VFO/ B ...
Other models in this manual:Car Receivers - TM-D710E (2.03 mb)