Votes - 3, Average rating: 4
(
)
)
|
manual abstract
However, each individual has personal preferences for how they like to set various functions. You have to keep changing many settings each time you use the transceiver. Because 5 PM channels are available, up to 5 persons can separately program the transceiver and store their customized environment. Then each person can quickly change to his or her favorite settings, simply by recalling a PM channel. It is too much trouble to change back the settings after somebody else has reconfigured them. So this application may avoid having a feature-rich transceiver but never using many useful features. While operating mobile on the way to work every morning, you prefer a silent transceiver that does not interrupt the morning calm. In addition, you feel that a bright display is a waste of electricity in sunlight. At night when driving home, you realize the Beep function truly serves a purpose and you feel it is nice to see a bright display after dark. In two PM channels, store the same operating data such as frequency, offset, tone, etc., and store different settings for the Display Dimmer and Beep functions. Then you can quickly recall the best settings for day or night operating. You cannot figure out how you can make the transceiver exit the current mode. Simply recall PM channel 1 that contains an exact copy of the transceiver default environment. You will not lose the contents of any memory channels. 43 8 8 1 Confirm that the following conditions have been satisfied: • The transceiver is in the receive mode. • Scan is not being used. • Microphone Control is OFF. 2 Configure the transceiver as you like. • For the items that can be stored, see page 42. 3 Press [F], [P.IN]. • The PM channel numbers 1 to 5 appear and blink at the bottom of the display. 4 Press [1] to [5] corresponding to the desired PM channel. • The settings listed in page 42 are stored in the PM channel. RECALLING A PM CHANNEL 1 Press [PM]. • The PM channel numbers 1 to 5 appear at the bottom of the display. 2 Press [1] to [5] corresponding to the desired PM channel. • The contents of the selected channel are recalled. • The current PM channel number appears at the upper right corner. “s” before “PM” indicates that Auto PM Store mode {page 45} has been selected. • To exit PM Recall mode, press [PM], then press [OFF]. Note: You cannot recall a PM channel while transmitting. 44 AUTO PM CHANNEL STORE AUTO PM CHANNEL STORE • You recall another PM channel. • You press [OFF]. • You switch OFF the transceiver. The factory default of this function is ON. 1 Press [MNU] to enter Menu mode. 2 Press [c ccccc]/ [d ddddd] to select “RADIO (1–)”, then press [OK]. 3 Press [c ccccc]/ [d ddddd] to select “MEMORY (1–4–)”, then press [OK]. 4 Press [c ccccc]/ [d ddddd] to select “AUTO PM STORE (1–4–1)”, then press [OK]. 5 Press [c ccccc]/ [d ddddd] to switch the function ON (default) or OFF. 6 Press [OK] to complete the setting. 7 Press [MNU] to exit Menu mode. PM CHANNEL RESET If you want to reprogram the PM channels from the beginning, reset all the PM channels to the factory defaults. 1 Press [PM]+ POWER ON. • A confirmation message appears. • Press [ESC] to quit resetting. 2 Press [OK]. You can also use Menu 1–9–7 (RESET) to reset the PM channels. See page 41. 8 45 46 9 SCAN This transceiver provides the following types of scans plus Visual Scan {page 47}. Visual Scan graphically and simultaneously shows how frequencies in a specific range are busy. Note: u Adjust the squelch level before using Scan. Selecting a squelch level too low could cause Scan to stop immediately. u While using CTCSS or DCS, Scan stops for any signal received; however, you will hear audio only when the signal contains the same CTCSS tone or DCS code that you selected. u When using S-meter Squelch, Scan stops when the received signal strength matches or exceeds the S-meter setting. Scan resumes 2 seconds after the signal level drops below the S-meter setting. u Pressing and holding Mic [PTT] causes Scan to temporarily stop if it is functioning on a non TX band. u Starting Scan switches OFF the Automatic Simplex Check. Scan is a useful feature for hands-off monitoring of your favorite frequencies. Becoming comfortable with all types of Scan will increase your operating efficiency. 145.430 MHz Stop Scan Type Scan Range VFO Scan All frequencies tunable on the band Memory Scan Frequencies stored in the memory channels Group Scan Frequencies stored in the memory channels which belong to the specified group Program Scan All frequencies in the range selected on the band MHz Scan All frequencies within a 1 MHz range Call/VFO Scan Call channel plus the current VFO frequency Call/Memory Scan Call channel plus the selected memory channel VISUAL SCAN VISUAL SCAN Selecting the Number of Channels While you are receiving, Visual Scan allows you to monitor frequencies near the current operating frequency. Visual Scan graphically and simultaneously shows how all frequencies in the selected range are busy. You...
Other models in this manual:Car Receivers - TM-D700A (2.43 mb)