Votes - 4, Average rating: 4.3 ( )

Manafacture: Kenwood File size: 1.45 mb File name: Language of manual:

Manual tuning : Press and hold until the desired station is received. About display change during tuner reception (remote control only) The display will change each time the DISPLAY key is pressed. 1Reception band/Frequency 2Preset number/Frequency 3Clock DISPLAY 28 Recording 28 Recording R-SG7/DP-SG7/X-SG7 (EN) Recording NoteNote Note that this cassette deck cannot record onto Metal tapes. 55 44 22 33 1133 Basic section1. Load a tape in deck. 1Open the tray of the cassette deck. 2Insert a tape. 3Close the tray. Top side Reverse side 11 NoteNoteNote 0 . Differentiation between normal (TYPE I) and high (TYPE II) tape is set automatically. O Remove tape slack before loading. Since longer tape than 100 minutes cassette tape is very thin, the tape could adhere to the pinch roller or be easily cut. It is recommended that these tapes not be used with this unit to prevent possible damage. 2. Select the tape transport direction. Check the tape transport direction indicator. To reverse the transport direction 1Press the playback key for the direction to be played (lights green). 23 2Stop playback (lights red). O When recording is started, the tape is transported in the direction selected in this step. . Wind the tape to the position where recording is to be started. Dolby NR rev. mode 3333 3. Set the recording condition. 1Select the reverse mode. . 2Select the DOLBY NR mode. . 29Recording 29Recording Temporary stop during recording 8 8 O Press the record key to restart recording. To interrupt recording An unrecorded section of about 4 sec is produced directly after the recording has been interrupted. 8 O Recording pause condition is reached after approximately 4 sec. R-SG7/DP-SG7/X-SG7 (EN) An unrecorded section of about 4 sec is produced (auto recording mute) 1Obtain stop condition. 2Press the record key twice. About 4 sec 8 . An unrecorded section of about 4 sec is produced and recording pause condition is reached. To end recording 7 Basic section 4. Select the source to be recorded. The input source component to be recorded input selector 44 should be displayed. R-SG7 CD Select an input source other than O When the CD input is selected and if a disc has been set “TAPE” input. in the CD player, its playback starts immediately. 5. Start recording. Lights ¦ 55 1Play (or tune) the input source to be recorded. 2Start recording. O The recording level is adjusted automatically when the CRLS function is used. . O Recording stops automatically when the tape side(s) to be recorded have been fully recorded. 30 Recording 30 Recording R-SG7/DP-SG7/X-SG7 (EN) To repeat a recording Return to the recording start position. Press the rewind key during recording. During recording of reverse side (while 2 is lit) 1 A During recording of top side (while 3 is lit) . If there is a non-recorded space of more than 4 seconds before the recording start position, recording is aborted and tape is rewound as shown below. Tape stops after 2 sec. of transport. Recorded tune Tune to be re-recorded Re-recording Blank of 4 sec. or more . If there is no recorded tune before, the tape will be rewound then stopped. Automatic Adjustment of the Recording Level (CRLS) A standard recording level has been set in advance for the cassette deck (X-SG7), but when the CRLS function is used, the max. recording level is set automatically for the music source. 1Play the contents to be recorded (or receive the radio station to be recorded). 2Press the CRLS key. Basic section About 20 sec CRLS CRLS CRLS If the key has never been pressed .....The sound is recorded with the basic level set with the unit. If the key is pressed .....The recording level is set automatically and stored in memory as the recording level to be used with the current input being selected. From the next time on, this recording level is set automatically for that input even if the key is not pressed. To return to the basic level .....Hold the key depressed until the indicator goes off (for approx. 3 seconds). . The recording level setting completes in approx. 20 seconds, after which the deck enters the record-pause mode. . If recording is started during the setting (while the CRLS indicator is blinking), distorted sound may be recorded. . If a non-recorded space of more than 3 seconds is detected after the CRLS key is pressed, the recording level setting is aborted. Points for Recording from a CD or an MD 1Pause the CD or MD to be played. For recording from a CD or an MD, playback from 2Use the skip keys (4 .) to select the title the music source and recording by the cassette deck can be started simultaneously (synchro recording to be recorded. (Pause will be reached at the function) when the cassette deck is set to record beginning of the selected title.) pause status in advance. 3Bring the cassette deck to recording pause condition. 4Start playback of the CD or MD. (Synchro recording will start.) . The recording is stopped when the stop key of the playback unit is pressed. Dolby HX Pro The Do...

Download now

Please, enter two numbers from picture: