Votes - 5, Average rating: 3.2 ( )

Manafacture: Kenwood File size: 1.2 mb File name: Language of manual:

Please install correctly according to the purchased components and connect the required cords. R-SE9T/DP-SE9/X-SE9 (En) Malfunction of microcomputer If operation is not possible or erroneous display appears even though all connections have been made properly, reset the microcomputer referring to “In case of difficulty”. W Audio cord (Supplied with R-SE9T) Preparation section DIGITAL OUTPUT OPTICAL DIGITAL IN OPTICAL Connection with Optical Fiber Cable This is used for digital connections. Digital trans- mission permits recording without loss of the high CD sound quality. Remove the cap and connect an optical fiber cable.Remove cap Optical fiber cable DP-SE9 DM-SE9 Audio cord (x2) (Supplied with X-SE9) R-SE9T X-SE9 (optional) [ ]Optional record player with internal RIAA equalizer/amp (P-100) or videodeck (etc.). SYSTEM CONTROL ANTENNAAMGND CD IN IN REC PLAY SUPER WOOFER PRE OUT SPEAKERS ( 6 - 16 ) LR TAPE TAPE REC PLAY MD MD AUX R R LL FM75 + - SYSTEM CONTROL REC IN PLAY OUT LR 11System connection 11System connection R-SE9T/DP-SE9/X-SE9 (En) Caution regarding placement To maintain proper ventilation, be sure to leave a space around the unit (from the largest outer dimen- sions including projections) equal to, or greater than, shown below. top panel : 50cm side panel : 10cm rear panel : 10cm Caution for Connection When connections are to be made, make sure that the power plug is not plugged into a wall AC outlet. Connect the equipment as shown in the figures. DP-SE9 DM-SE9 (optional) Optical fiber cable (Supplied with DM-SE9) Audio cord (x2) (Supplied with DM-SE9) Ventilation fan The ventilation fan runs high-power reproduction. To allow for proper ventilation, do not block the ven- tilation fan. LR DIGITAL IN OPTICAL SYSTEM CONTROL REC IN PLAY OUT 1 2 DIGITAL OUTPUT OPTICAL SYSTEM CONTROL LINE OUTPUT LR Preparation NotesNotes 1.In case an associated system component is connected, also read the instruction manual of the component. 2.Insert the optical-fiber cable straight into the connector until it clicks. 3.Be sure to attach the protection cap when the connector is not used. 4.Be careful not to bend, coil or bundle the optical fiber cable. 12 System connection 12 System connection R-SE9T/DP-SE9/X-SE9 (En) 3. Connection of speakers Connect the speakers as shown in the figure. Do not plug the power cord into a wall AC outlet until the connection has been completed. Preparation section 1Cord preparation. 2Loosen. 3Insert. 4Secure. 1Secure. 2Insert. • Sound will not be heard if the speaker terminal is not fully secured. Connection of banana plugs Speaker (right) Speaker (left) (6-16W) (6-16W) · ¦Never short-circuit the + and – speaker cords. The protection circuit will operate and no sound will be put out. SYSTEM CONTROL ANTENNAAMGND CD IN REC PLAY SUPER WOOFER PRE OUT SPEAKERS ( 6 - 16 ) R TAPE TAPE REC PLAY MD MD AUX FM75 + - IN L R L R L SPEAKERS ( 6 - 16 ) LR SUPER WOOFER PRE OUT R-SE9T »»a ¦If the left and right speaker connections or the + and – polarity are inverted, the sound will be unnatural with unclear localization of musical instruments, etc. Be sure to connect them without mistake. Super woofer (SW-500) (optional) Extremely low frequency sound is played back powerfully. This can be used with any type of playback. 13System connection 13System connection R-SE9T/DP-SE9/X-SE9 (En) 4. Connection of system control cord Connect the system control cords and the power cords as shown in the figure. System control cord (Supplied with R-SE9T) AC outlet AC outlet SYSTEM CONTROL ANTENNAAMGND CD IN IN REC PLAY SUPER WOOFER PRE OUT SPEAKERS ( 6 - 16 ) LR TAPE TAPE REC PLAY MD MD AUX R R LL FM75 + - SYSTEM CONTROL REC IN PLAY OUT LR LR DIGITAL IN OPTICAL SYSTEM CONTROL REC IN PLAY OUT 1 2 DIGITAL OUTPUT OPTICAL SYSTEM CONTROL LINE OUTPUT LR To wall AC outlet To wall AC outlet To wall To wall System control cord (Supplied with X-SE9) R-SE9T DM-SE9 (optional) DP-SE9 X-SE9 (optional) System control cord (Supplied with DM-SE9) Preparation Connection of system control cord Insert the plug straight into the connector until it locks. Plugging the connector While pushing the two sides of connector in, pull it straight out. Unplugging the connector 5. Power Cord Connection Insert the power cord plug into a wall AC outlet after all other connections have been completed. NotesNotes 1.Be sure to insert all connection cords securely. If their connections are imperfect, the sound may not be produced or noise may interfere. 2.Before plugging or unplugging a connection cord, be sure to unplug the power cord from the wall AC outlet. If connection cords are plugged or unplugged with the power cord left plugged in, malfunction or damage may result. 14 Controls and indicators 14 Controls and indicators R-SE9T/DP-SE9/X-SE9 (En) Main Unit TUNED indicator Stereo reception indicator RDS display AUTO indicator Sleep timer indicator MUTE indicator ********; TUNED RDS EON PTY TPST.AUTOMUTE N.B. SLEEP TA NEWS INFO A.P.S. O.T.T. kHz MEMO. MHz...

Download now

Please, enter two numbers from picture: