Votes - 3, Average rating: 4.3 ( )

Manafacture: Kenwood File size: 530.11 kb File name: Language of manual:

2WARNING FM/AM antenna input Rear left output Rear right output Fuse (5A:KDC-X915) (10A:KDC-X815/9015) KENWOOD disc changer / DAB control input / Display Data Output Jack Wiring harness (Accessory1) White/Black Gray/Black Green/Black Purple/Black White Gray Green Purple To front left speaker (KDC-X815/9015 only) To front right speaker (KDC-X815/9015 only) To rear right speaker (KDC-X815/9015 only) To rear left speaker (KDC-X815/9015 only) Ignition wire (Red) Battery wire (Yellow) Ground wire (Black) - (To car chassis) Ignition key switch Car fuse box (Main fuse) ACC Car fuse box Battery If no connections are made, do not let the wire come out from Front left output (White) Front right output (Red) Non-fading right output (KDC-X915/X815 only) To connect the Disc changer or DAB unit, consult each manual. NOTE Power control wire (Blue/White) Motor antenna control wire (Blue) Dimmer control wire (Orange / White) When using the optional power amplifier, connect to its power control terminal. To car light control switch Depending on what antenna you are using, connect either to the control terminal of the motor antenna, or to the power terminal for the booster amplifier of the film-type antenna. External amplifier control wire (Pink / Black) (KDC-X915/X815 only) To "EXT.AMP.CONT." terminal of the amplifier having the external amp control function. DC/DC converter (Wrap the cushion (Accessory! ) around this box.) Separate this box from the unit antenna cords. If they are too may cause the reception to get noise. 2CAUTION Outputs data representing the unit's current state, causing it to appear in the external display.To connect to this jack, a converting adapter (optional) is necessary. Non-fading left output (White) (KDC-X915/X815 only) — 44 — Installation Locking Locking Installation Bend the tabs of the mounting sleeve with a screwdriver or similar utensil and attach it in place. Accessory2 Metal mounting strap Phillips truss head sheet metal screw (commercially Firewall or metal support Accessory4 available) NOTE Make sure that the unit is installed securely in place. If the unit is unstable, it may malfunction (for example, the sound may skip). Locking the If you want to lock fall off, follow the 1 Refer to the function remove the faceplate. 2 Insert the provided screw into bottom side of the faceplate which the unit. Accessory7 3 Refer to the section "Removing the faceplate (page then reattaching the faceplate. 2CAUTION Never insert the taptite screws ( o2 . 6 mm) in any other screw holes than the one specified. If you insert it in another hole, it will contract and may cause damage to the mechanical parts inside the unit. 2CAUTION To attach this unit, make sure the front of the control panel faces you and fit it into the mounting sleeve by pressing the four corners of the hard rubber frame at the same time. Do not apply strong pressure to other sections than the corners; otherwise troubles such as the impossibility of opening or closing the panel may result. — 45 — Removing English Removing Insert the removal frame, and pull it Accessory0 Removal tool Removing 1 Make the faceplate 2 Refer to the section “ Removing the hard and then remove the hard 3 Remove the hex head machine on the back panel. 4 Insert the removal tool deeply, left and the R on the right. L Accessory4 Accessory3 Removal tool NOTE If the unit is removed while the faceplate is closed, use the removal tool with the left and right reversed, as illustrated. 5 Push upward the both tools, as shown, and pull the unit toward you until it is halfway out. The unit may drop if you pull it out completely. 6 Pull the unit all the way out with your hands, being careful not to drop it. L L R — 46 — Installation Installing LTN T N RTN T N On the factory-installed the tabs or holes that those used for screws), similar utensil. 8mm 5mm 5mm 8mm After aligning the J-Car bracket with the factory-installed radio bracket, tighten the screws. Damage to the unit will result from using screws other than those provided. 2CAUTION Accessory6 for Toyota car Accessory5 for Nissan car TabHole Once you have affixed the factory-installed radio bracket with the screws, use a standard-tipped screwdriver (not Philips) or similar utensil to pry the tabs of the J-Car bracket to make them fit into the holes in the factory-installed radio bracket (depending on the car make). Tab N … Nissan car T … Toyota car Factory trim bezel Accessory8 J-Car Bracket (follow indications for L/R) Accessory9 J-Car Trim Plate (place thick part on bottom) Factory-installed Radio Bracket Factory-installed Radio Bracket — 47 — Troubleshooting What might Before calling PROBLEM POSSIBLE CAUSE SOLUTION The power does not turn The fuse has blown. After checking for short fuse with one with the same No sound can be heard, or the Attenuator is turned on. Turn off Attenuator. volume is low. The fader or balance settings are set Reset the fader or balance settings. side. The input/output wires or wiring h...

Download now

Please, enter two numbers from picture: