to .. CD (..) ....: F Folder : AAudio file .... ..... ... ... ..... ..... ... ..... ... ..... ..... An online manual about audio files is put on the site, On this online manual, detailed information and notes which are not written in this manual are provided. Make sure to read through the online manual as well. Handling CDs • Do not touch the recording surface of the CD. • Do not stick tape etc. on the CD, or use a CD with tape stuck on it. • Do not use disc type accessories. • Clean from the center of the disc and move outward. • When removing CDs from this unit, pull them out horizontally. • If the CD center hole or outside rim has burrs, use the CD only after removing the burrs with a ballpoint pen etc. CDs that cannot be used • CDs that are not round cannot be used. • CDs with coloring on the recording surface or CDs that are dirty cannot be used. • This unit can only play the CDs with . This unit may not correctly play discs which do not have the mark. • You cannot play a CD-R or CD-RW that has not been finalized. (For the finalization process refer to your CD-R/CD-RW writing software, and your CD-R/CDRW recorder instruction manual.) English | 5 General features .................... Release button Control knob Auxiliary input ....5 ....$ ATT indicator Clock display Power Turning ON the Power Press the [SRC] button. . • When the power is ON, the (page 16) is displayed as "CODE ON" or "CODE OFF". (Function of KDC-MP4036AX) Turning OFF the Power Press the [SRC] button for at least 1 second. Selecting the Source Press the [SRC] button. Source required Display Tuner "TUNER" CD "CD" External disc (Optional accessory)** "CD CH" Auxiliary input* "AUX" Auxiliary input (Optional accessory)** "AUX EXT" Standby (Illumination only mode) "STANDBY" 6 | English * An equipment such as a portable audio player can be connected to the auxiliary input terminal using a commercially available mini-plug (3.5o). (Function of KDC-MP4036AX/KDC-MP3036AX/KDC-MP336AX) . • ** Function of KDC-MP4036AX • Use the mini-plug which is stereo type and does not have any resistance. Volume Increasing Volume Turn the [VOL] knob clockwise. Decreasing Volume Turn the [VOL] knob counterclockwise. Attenuator Turning the volume down quickly. Press the [ATT] button. Each time you press the button, the Attenuator turns ON and OFF. When the Attenuator is ON, the "ATT" indicator blinks. Audio Control 1 Select the source to adjust Press the [SRC] button. 2 Enter Audio Control mode Press the [VOL] knob. 3 Select the Audio item to adjust Press the [VOL] knob. Each time you press the knob, the item to be adjusted alternates between the items shown in the table below. 4 Adjust the Audio item Turn the [VOL] knob. Adjustment Item Display Range Subwoofer level "SW L" –15 — +15 System Q "NATURAL"/"ROCK"/ Natural/Rock/Pops/Easy/ "POPS"/"EASY"/ Top 40/Jazz "TOP40"/"JAZZ" Bass level "BAS L" –8 — +8 Middle level "MID L" –8 — +8 Treble level "TRE L" –8 — +8 Balance "BAL" Left 15 — Right 15 Fader "FAD" Rear 15 — Front 15 Exit Audio Control mode (Volume control mode) . About System Q • You can recall the best sound setting preset for different types of music. • Change each setting value with the (page 8). First, select the speaker type with the Speaker setting. • "USER": This appears when Bass level, Middle level, and Treble level are adjusted. When "USER" is selected, these levels are recalled. 5 Exit Audio Control mode Press any button. Press a button other than the [VOL] knob and [ATT] button. Audio Setup Setting the Sound system, such as Volume offset. 1 Select the source to adjust Press the [SRC] button. 2 Enter Audio Setup mode Press the [VOL] knob for at least 1 second. 3 Select the Audio Setup item to adjust Press the [VOL] knob. Each time you press the knob, the item to be adjusted alternates between the items shown in the table below. 4 Adjust the Audio setup item Turn the [VOL] knob. Low Pass Filter Adjustment Item Display Range "LPF" 80/120/160/Through Hz Volume offset "V-OFF" –8 — ±0 (AUX : –8 — +8) . • Volume offset: Sets each source’s volume as a difference from the basic volume. 5 Exit Audio Setup mode Press the [VOL] knob for at least 1 second. Bass Boost Bass sound can be enhanced by one-touch operatin. Press the [B.BOOST] button. When you press the button once, the current Bass Boost setting is displayed. Each time you press the button, the Bass Boost setting alternates. Setting Display Bass Boost 1 "BB-L L1" Bass Boost 2 "BB-L L2" Bass Boost off "BB-L OFF" English | 7 General features Speaker Setting Fine-tuning so that the System Q value is optimal when setting the speaker type. 1 Enter Standby Press the [SRC] button. Select the "STANDBY" display. 2 Enter Speaker Setting mode Press the [VOL] knob. 3 Select the Speaker type Turn the [VOL] knob. Each time you turn the knob, the setting alternates between the settings shown in the table below. Speaker type Display OFF "SP OFF" For 5 & 4 i...
)
