Votes - 2, Average rating: 4 ( )

Manafacture: Kenwood File size: 812.48 kb File name: Language of manual:

If this procedure is not carried out, the control panel of the unit will re-open in two seconds even with your vehicle's ignition turned off. • When the control panel of the faceplate is hidden, the unit will be locked by the sleeve, making it more difficult to remove the unit. • When the moving faceplate is hit by an object, it will stop and return to its original state. Remove the object and repeat the action. 2 CAUTION Using the Unit in Vehicles with Covered Consoles ATT indicator . indicator • Make sure the console is uncovered whilst the faceplate is reversed. • Do not exert any excess force on the movable parts of the unit, including the faceplate, as it can cause failure in the unit’s mechanism. Switching Modes Switching Modes: LOUD indicator — 6— Each time you follows: t Tuner mode t Tape mode t External disc control mode 1 t External disc control mode 2/AUX mode t Standby mode Selecting the standby mode: Press the SRC button repeatedly to select to "When "ALL OFF" is displayed, the standby mode The standby mode turns all functions off although unit’s power on. Use this mode when you want to have display illuminated but do not want to listen to anything. NOTE • The mode switches to the next mode from any mode which cannot be used. • The external disc control mode will differ depending on the unit that is connected. • The AUX mode is available only when the changer / AUX switching adapter (KCA-S210A or CA-C1AX) or CD changer (KDC-CPS85, KDC-CX85, KDC-CPS82 or KDC-CX82) is connected to this unit. During the AUX mode, "AUX" / AUX-name will show in the display. When the CA-C1AX is being used, the AUX Mode will replace the External Disc Control Mode. NOTE Presetting AUX-name In the AUX mode, press the NAME.S button for two seconds or more. "NAME SET" is display and AUX-name mode is entered. Input the characters, referring to the section on "Presetting Disc Names (DNPS)" (page28). Volume Increasing Volume: Press the u button to turn up the volume. Decreasing Volume: Press the d button to turn down the volume. Attenuator This function allows you to turn down the Turning Attenuator On/Off: Press the ATT button to switch the attenuator on When the attenuator is on, the ATT indicator blinks. When the attenuator is off, the volume returns to the level. NOTE Turning the volume up, or turning it all the way down deactivates the attenuator function. Loudness This function amplifies low and high tones when the volume is turned down. The LOUD indicator lights up, when the loudness function is on. Turning Loudness On/Off: Hold down the LOUD button for one second or more to switch the loudness on and off. NOTE The loudness function does not affect non-fading pre-out. — 7— English General features Forced Closing This function prevents being serviced etc. Hiding the unit with the ignition turned on (forced closing): Hold down the SRC button The faceplate will slide open. you have set in the "Time setting the menu has passed, the faceplate hide the control panel. However, you during that period. For details, refer to the faceplate" (page10). NOTE • When the closing faceplate is hit by an object, the off without the faceplate closing all the way. Remove and press the SRC button to turn the unit back on, then off again to make it close properly. • Whilst the control panel is moving, pressing the buttons will have any effect. Do not try to press the buttons on the control panel as the faceplate is moving, as excessive force may damage the unit. • During the forced closing of the unit (i.e., having the unit left closed whilst ignition is turned on), the faceplate will not open no matter how often the ignition is turned on or off, unless "Manual Open button" at the rear of the faceplate is pressed in order to open it. You can prevent tampering of the unit when letting someone else drive your car by keeping it closed this way. To cancel the forced closing of unit and open control panel: Press the left part at the upper side of the faceplate for as many times as you have preset in the "Manual Open Button Setting" (OPEN SW #) in the menu. The faceplate will open and show the control panel. NOTE When you set the Manual Open Button setting to 2 or 3, press the upper left part of the faceplate without pausing. If you do not press that part without pausing, the command cannot be verified correctly. Faceplate Angle Adjustment You can adjust the faceplate angle for easy viewing. Adjusting faceplate angle: Press the A (EJECT) button to make the faceplate slide open, and then adjust the faceplate angle using the angle adjustment switch. Adjustment may be made from 0 to 2. 0 1 2 0 1 2 02 1 NOTE • Firmly slide the switch until it clicks. • Do not apply excessive force to the faceplate under settings 1 or 2. • Set the angle adjustment switch to "0" before removing the faceplate. — 8— Function of the KRC-778R/KRC-778RV Function of the KRC-PS978R/KRC-878R Function of the KRC-PS978R/KRC-878R Switching Display Non-Fading Output You can change...

Download now

Please, enter two numbers from picture: