When the Security Code function is activated, the code can't changed and the function can't be released. Note, the Security Code can be set as the 4 digit number of your choice. 1 Select the Security Code mode Press the [FM] or [AM] button. Select the "Security" display. 2 Enter the Security Code mode Press the [S.A] button for at least 2 seconds. "WRITE!" is displayed. 3 Enter the Security Code Press the [1] — [4] button. Example: If the Security Code is "3510". Step Button #Times pressed Display Press the Reset button and battery power source 1 Turn the power ON. 2 Do the step 3 and 4 operation, and enter "CODE OK!" is displayed. The unit can be used. Tuning Mode Sets the tuning mode. Tuning mode Display Operation Auto seek "Auto 1" Automatic search for a station. Preset station seek "Auto 2" Search in order of the stations in the Preset memory. Manual "Manual" Normal manual tuning control. 1 [1] 4 "3" 2 [2] 6 "5" 3 [3] 2 "1" 4 [4] 1 "0" 4 Confirm the Security Code Press the [S.A] button. When "WRITE!" is displayed, "RE-ENTER" is displayed. Monaural Reception Noise can be reduced when stereo broadcasts are received as monaural. Display "MONO Off" "MONO On" Setting The monaural reception is OFF. The monaural reception is ON. — 25 — Basic Basic Function Auto Memory English For the operation method 16). (page 8) . [ATT] button Turning the volume down quickly. When it is pressed again it returns to the previous level. [FM]/ [AM] buttons Select the band. Each time the [FM] button FM1, FM2, and FM3 bands. [4]/ [ . ] buttons Tune up or down band. [0] — [9] buttons Press buttons [1] — [6] to recall preset stations. [DIRECT] button Enters and cancels the (page 15) mode. In Cassette tape source [4]/ [ . ] buttons Do (page 18). [ 38] button Plays the reverse side of the tape. [FM] button Fast forwards the tape. When the [ 38] button is pressed it releases. [AM] button Rewinds the tape. When the [ 38] button is pressed it can be released. [0] — [9] buttons When in (page 18) enter the number of songs. — 27 — English English Accessory In Disc source [4]/ [ . ] buttons Doing track/ file forward [DISC+]/ [DISC–] buttons Doing disc/ folder forward and [ 38] button Each time the button is pressed the song [0] — [9] buttons When in (page 21) and (page 21), enter the track/disc number. — 28 — Accessories Accessories External view External view ......... Number of ......... Number of (M5.6mm) 3 ......... 6 ......... 1 (M5.7mm) 4 ......... 1 ......... 6 The use of any accessories except for those provided damage to the unit. Make sure only to use the accessories the unit, as shown above. Installation Procedure 1. To prevent a short circuit, remove the key from the ignition and disconnect the - battery. 2. Make the proper input and output wire connections for each unit. 3. Connect the speaker wires of the wiring harness. 4. Connect the wiring harness wires in the following order: ground, battery, ignition. 5. Connect the wiring harness connector to the unit. 6. Install the unit in your car. 7. Reconnect the - battery. 8. Press the reset button. 2WARNING If you connect the to the car chassis (ground), turn may start a fire. Always source running through the 2CAUTION • If your car's ignition does not have ignition wires to a power source that with the ignition key. If you connect the ignition wire to a power source with a constant voltage supply, as with battery wires, the battery may die. • If the fuse blows, first make sure the wires aren’t touching to cause a short circuit, then replace the old fuse same rating. • Insulate unconnected wires with vinyl tape or other material. To prevent a short circuit, do not remove the caps on the ends of the unconnected wires or the terminals. • Connect the speaker wires correctly to the terminals to which they correspond. The unit may be damaged or fail to work if you share the - wires or ground them to any metal part in the car. • When only two speakers are being connected to the system, connect the connectors either to ...
)
