Votes - 2, Average rating: 4
(
)
)
|
Photos and specs LG LCS325UB |
manual abstract
Align the left side of the panel with the stopper. 2. Push the right side of panel into the unit until it clicks. .The control buttons may not work properly if the control panel is not attached properly. If this occurs, gently press the display. .Do not leave the control panel in any area exposed to high temperatures or direct sunlight. .Do not drop the control panel or otherwise subject it to strong impact. .Do not allow such volatile agents as benzine, thinner, or insecticides to come into contact with the surface of the control panel. >Caution Detaching the control panel Note 1. Press the 6 to open the control panel. Periodically wipe the contacts on the back of the control panel with a cotton swap moistened with alcohol. For safety, turn off the ignition before cleaning, and remove the key from the ignition switch. , 2. Lift the control panel slightly. 3. Push the control panel to right. 5 6 4. Pull the control panel out of the unit. 5. Put the detached control panel into the protective case. Control panel Protective Case Connecting 7 Connection Connecting to a car Before installing, make sure that the ignition-switch is set to OFF and remove the terminal of the car battery to avoid short-circuiting. B a Not connected abcd efgh abcd efgh a b c d e f g h AAAAAAAAPower Antenna Control Relay To Audio out (Optional) Rear Left (Sub-woofer Left) Front Left Rear Right (Sub-woofer Right) Front Right Amplifi er B f Power Antenna (Blue) B gNot connected B cTo Ignition (Red) B h Ground (-) (Black) B dTo Battery (+) (Yellow) B bNot connected Ignition Switch Wired remote input (Black): Hard-wired control adapter can be connected. (Optional) B e Remote On (Blue / White) (Optional) 2 To Audio in (Optional) Amplifi er Connecting When being connected in a wrong way, the unit displays as follows. - Antenna / Remote port short: "ANTENNA/ REMOTE ON PORT SHORT CIRCUIT CHECK" After connecting it again, restart the unit. >Caution A a Gray : Front Right + A b Gray / Black Stripe: Front Right - A cViolet : Rear Right + A dViolet / Black Stripe: Rear Right - A eWhite : Front Left + A fWhite / Black Stripe: Front Left - A g Green : Rear Left + A h Green / Black Stripe: Rear Left - 8 Operating Operating 3 Operation Basic operations 1. Turn the unit on by pressing any key on the unit. 2. Select a source by pressing SRC. 3. Rotate the volume knob to adjust the volume on the unit. Or press VOLUME W / S on the remote control. Turning off the sound temporarily 1. Press MUTE to mute your unit. Or press MUTE on the remote control. 2. Press it again to cancel Using EQ (Equalizer) EQ is to increase or decrease the signal strength of audio frequencies. The function helps you to enjoy sound more plentifully. Press EQ on the unit repeatedly. The indicator lights up in the following order. B-BOOST (BASS BOOSTER) / POP / CLASSIC / ROCK / JAZZ /VOCAL / SALSA / SAMBA / REGGAE / RUSSY /USER1 / USER2 / Off (Not displayed) Using 3D SOUND This mode delivers outstanding surround sound. 1. Press and hold EQ/ • 3D. 2. Press and hold it again to cancel. 3D SOUND is only available when you use the CD/ USB. , Note Checking the clock 1. Press DISP 2. Press it again to cancel Turning off the display light 1. Press and hold DISP. 2. Press and hold it again to turn it on. Under the light-off condition, press any key, the light is turned on and then off automatically if you don't press it within a few seconds. , Note Resetting the unit You can reset the unit when it does not operate properly. 1. Detach the control panel. Refer to page 6 for detaching the control panel. 2. Press the RESET hole with a sharp object. Adjusting the general settings You can adjust [SOUND], [LIGHT] and [OTHER] settings. On the unit 1. Press MENU. 2. Rotate the volume knob to select [SOUND], [LIGHT], or [OTHER] and press it. 3. Rotate the volume knob to select the item and press it. 4. Rotate the volume knob clockwise or counterclockwise to adjust the level. 5. Press the volume knob to confirm the setting. If you want to return to the previous step, press . On the Remote Control 1. Press and hold FUNC / • MENU. 2. Press w / s to select [SOUND], [LIGHT], or [OTHER] and press ENTER. 3. Press w/ s to select the mode and press ENTER. 4. Press w/ s to adjust the level. 5. Press ENTER to confirm the setting. If you want to return to the previous step, press . For [SOUND] setting You can adjust sound quality by adjusting the level BAL (left/right speaker), FAD (front/rear speaker), SW (Subwoofer), SW-F (Subwoofer frequency), A-EQ (Auto EQ). -When you set the EQ to USER 1/2 mode. : You can adjust the level of BAS (bass), MID (middle), TRB (treble). • SW (Subwoofer, LCS321UB only) You can adjust the volume of subwoofer. • SW-F (Subwoofer frequency, LCS321UB only) OFF/ SW 55 Hz/ SW 85 Hz/ SW 120 Hz You can enable the subwoofer. • A-EQ (Auto EQ) OFF / ON AUTO EQ operates only in the music file supported with genre in the device. When you set AUTO EQ to ON, POP, CLASSIC, ROCK, or JAZZ is automatic...