Votes - 4, Average rating: 4.8
(
)
)
|
manual abstract
TA SEEK : When the tuned station does not receive TP information for 5 seconds, the receiver retunes to the next station that has the TP information. • PI (Programme Identification) SOUND / MUTE PI SOUND : If the sound of a station with different PI is heard intermittently, the receiver mutes the sound after 1 second. PI MUTE : If the sound of a station with different PI is heard intermittently, the receiver mutes the sound right now. • C-T(Clock Time) ON/OFF You can use the RDS CT information to update the time. When RDS CT information is not received and then you set CT to OFF, you can adjust the time by yourself. Refer to the page 10 for setting the clock. • AUX (Auxiliary) ON / OFF It is possible to use auxiliary equipment with this unit. Activate the auxiliary setting when using auxiliary equipment connected to this unit. • AUX (Auxiliary) 00dB / +6dB Only when you set AUX to ON as switching sources, you can adjust the volume level of each source to prevent radical changes in volume. You can set to 0 dB or +6 dB. You may be surprised at a loud sound when you change the source from the external component to another source. • DEMO OFF/ ON You can change the initial indication on the display to information name (function name, EQ name, etc...) while listening to a source. • LCD WHI / RED You can change the LCD window color. WHI(white) <-> RED(red) • [LAC5900RN] LED RED / GRN / AUTO [LAC6900RN] LED BLU / RED / AUTO: You can change the button color. • COL TM (Color changing time) Only when you set LED to AUTO, you can set LED color changing time from 5 to 60 seconds. • SW(Subwoofer) OFF / SW 55HZ / SW 85HZ / SW 120 HZ You can enable the subwoofer. SW OFF <-> SW 55HZ <-> SW 85HZ <-> SW 120 HZ. • DIM(Dimmer) OFF / ON / AUTO You can change the brightness of the display window during the power-on status. When you set DIMMER to AUTO, the dimmer operates according to the car dimmer setting. • DIM L (Dimmer Level) When you set DIM to ON/AUTO, you can adjust the dimmer level. (-2,-1,0,+1,+2) • A-EQ(Auto EQ) ON/OFF AUTO EQ operates only in the music file supported with Genre in the device. When you set AUTO EQ to ON, POP, CLASSIC, ROCK, or JAZZ is automatically selected according to the music genre. • BEEP 2ND / ALL BEEP 2ND : The beep is generated when a key is long pressed. (1 sec) BEEP ALL : The beep is generated when any key is pressed. CAR CD/MP3/WMA Receiver 13 Troubleshooting Symptom Cause Correction Power doesn’t turn on / The unit doesn’t operate. No sound is heard / The vol- ume level will not rise. There’s audio skipping. The playback is not possi ble. Radio stations cannot be tuned in. The unit does not operate correctly even when the appropriate remote control buttons are pressed. Leads and connectors are not properly. The fuse is blown. Noise and other factors are causing the built- in microprocessor to operate incorrectly. Cables are not connected correctly. This unit is not firmly secured. The disc is dirty. The loaded disc is of a type this unit cannot play. The signal strength of the stations is too weak(when tuning in with automatic tuning.) No station has been preset or preset stations have been cleared(when tuning by scanning preset stations.) Battery power is low. Confirm once more that all connections are correct. Rectify the problem that caused the fuse to blow, and then replace it. Be very sure to install the correct fuse with the same rate. Turn the unit off and then on. Connect the cables correctly. Secure this unit firmly. Clean the disc. Check what type the disc. Tune in the stations manually. Preset the stations.(Refer to the page 12) Load new battery. General CD Radio Remote control Symptom Cause Correction Power doesn’t turn on / The unit doesn’t operate. No sound is heard / The vol- ume level will not rise. There’s audio skipping. The playback is not possi ble. Radio stations cannot be tuned in. The unit does not operate correctly even when the appropriate remote control buttons are pressed. Leads and connectors are not properly. The fuse is blown. Noise and other factors are causing the built- in microprocessor to operate incorrectly. Cables are not connected correctly. This unit is not firmly secured. The disc is dirty. The loaded disc is of a type this unit cannot play. The signal strength of the stations is too weak(when tuning in with automatic tuning.) No station has been preset or preset stations have been cleared(when tuning by scanning preset stations.) Battery power is low. Confirm once more that all connections are correct. Rectify the problem that caused the fuse to blow, and then replace it. Be very sure to install the correct fuse with the same rate. Turn the unit off and then on. Connect the cables correctly. Secure this unit firmly. Clean the disc. Check what type the disc. Tune in the stations manually. Preset the stations.(Refer to the page 12) Load new battery. General CD Radio Remote control CAR CD/MP3/WMA Receiver Specifications General Output Power 53W x 4CH (Ma...
Other models in this manual:Car Receivers - LAC5900RN (1014.55 kb)
Car Receivers - LAC5900RNP2 (1014.55 kb)