Votes - 4, Average rating: 3.5
(
)
)
|
manual abstract
This product is manufactured to comply with Directive 2005/83/EEC(ANNEX I , 3.2.9), 72/245/EEC, and 2006/95/EC. 4 Before use Detaching the control panel The control panel of this unit can be detached to prevent theft. 1 Press the (RELEASE) to open the control panel. 2 Hold the right part of the control panel. 3 Pull out the control panel. 4 Place the control panel in the supplied protective case. Protective Case 4 3 Control panel 2 1 Before use Detaching the control panel The control panel of this unit can be detached to prevent theft. 1 Press the (RELEASE) to open the control panel. 2 Hold the right part of the control panel. 3 Pull out the control panel. 4 Place the control panel in the supplied protective case. Protective Case 4 3 Control panel 2 1 Attachable control panel The control panel of this unit can be detached to prevent theft. 1 Align the left side of the panel with the stopper. 2 push the right side or panel into the unit until it clicks. Caution • When detaching or attaching the control panel, do not press control buttons. • The control buttons may not work properly if the control 2 panel is not attached properly. If this occurs, gently press the display. 1 temperatures or direct sunlight. • Do not leave the control panel in any area exposed to high • Do not drop the control panel or otherwise subject it to strong impact. • Do not allow such volatile agents as benzine, thinner, or insecticides to come into contact with the surface of the control panel. 5 Control Panel Control Panel 1 EJECT Z 11 Select [SEL S] 2 [MUTE] 12 • Search -m 3 • Skip M?+ • Tune -m • Seek M?+ 13 Preset Station [1-6] 4 Remote Sensor - Optional 14 • MP3 Track +10/-10 [F+/F-] 5 • Volume • Folder Up/Down [F+/F-] • Power [PWR] 15 Shuffle [SHF] 6 • Auto Store [AS] 16 Repeat [RPT] • Preset Scan [PS] 17 Intro Scan [SCAN] • Equalizer [EQ] 18 Play/Pause B X 7 DISC SLOT 19 Extreme Dynamic Sound System [XDSS] 8 • Search M + 20 [BAND] • Tune M + 21 • Skip -? ?? m mm 9 Display [DISP (CLOCK)] • Seek -? ?? m mm 10 Release 22 SOURCE [SRC S SS ] WMAMP3 WMAMP3 6 WMAMP3 Remote control (optional) 1 Power [POWER] / Mute 1 2 Select [SEL] 3 Source [SRC]2 10 4 Play / Pause B/X 3 11 5 Intro Scan [SCAN] 4 6 Shuffle [SHF] 12 WMAMP3 WMAMP3 5 13 7 • MP3 Track +10 6 14 • Folder Up [F+] 7 8 • CD Skip / Search ?m m 15 8 • Seek / Tune ?m m 9[BAND] 16 9 10 Volume Up / Down 17 11 Number [#] 12 Repeat [RPT] 13 Preset Station [1-6] 14 Number [0 -9] 15 • CD Skip / Search M M? • Seek / Tune M M? 16 Display [DISP.] 17 • MP3 Track -10 MP3 WMA • Folder Down [F-] Battery installation 1 Pull out the battery holder with a sharp product like a ball point pen. 2 Put the battery with holder. and correctly on the battery 3 Install the battery holder back into its original position. Note • Use only one CR2025 (3V) lithium battery. • Remove the battery if the remote control is not used for a long period of time. • Do not leave the product in a hot or humid place. • Do not handle the battery with metallic tools. • Do not store the battery with metallic materials. 7 Installation Installation Bend the claws according to the thickness of the dashboard Control panel 5 4 3 1 26 Control panel Basic Installation Before installing, make sure that the ignition-switch is set to OFF and remove the terminal of the car battery to avoid short-circuiting. 1 Remove the existing receiver unit. 2 Make the necessary connections. 3 Install the installation sleeve. 4 Install the unit into the installation sleeve. Removing the existing receiver unit. If there is already an installation sleeve for the receiver unit in the dashboard, it must be removed. 1 Remove the rear support from the unit. 2 Remove the control panel and trim ring from the unit. 3 Insert the lever Ainto the hole on one side of the unit. A A Perform the same operation on the other side and pull the unit out from the mounting sleeve. ISO-DIN Installation 1 Slide the unit into the ISO-DIN frame. 2 Fit screws removed from the old unit. 3 Slide the unit and frame into the dash opening. 4 Install the dash panel or adapter plate. 5 Install the trim ring to the unit. 6 Install the control panel to the unit. 8 Connection diagram Connection diagram Before connecting, make sure that the ignition switch is set to OFF, and remove the battery # terminal to avoid short circuits. 9 BATTERY POWER Antenna DIMMER SWITCH IGNITION SWITCH CONTROL RELAY REMOTE ON (BLUE/WHITE) AMPLIFIER (Optional) PHONE MUTE (ORANGE) DIMMER (PINK) TO IGNITION (RED) GROUND(-) (BLACK) POWER ANTENNA (BLUE) TO BATTERY(+) (YELLOW) 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 B A A A A A A A A 1 2 4 5 6 7 8 1 2 3 4 5 6 7 8 AABB CC B 11. Violet : Rear Right + B 22. Violet/ Black Stripe : Rear Right – B 33. Gray : Front Right + B 44. Gray / Black Stripe : Front Right – B 55. White : Front Left + B 66. White/Black Stripe : Front Left – B 77. Green : Rear Left + B 88. Green/ Black Stripe : Rear Left – To Speaker To Vehicle (Optional) (Optional) rr Connection Connection C CCSpeaker Connec...