Votes - 12, Average rating: 3.9 ( )

Manafacture: Pioneer File size: 2 mb File name: Language of manual:

Photos and specs  Pioneer  DEH-2300UB

2 Turn M.C. to adjust the source volume. Adjustment range: +4 to –4 3 Press M.C. to confirm the selection. Initial Settings Important PW SAVE (power saving) is cancelled if the vehicle battery is disconnected and will need to be turned back on once the battery is reconnected. When PW SAVE (power saving) is off, depending on connection methods, the unit may continue to draw power from the battery if your vehicle's ignition switch doesn't have an ACC (accessory position). 1 Press and hold S (SRC/OFF) until the unit turns off. 2 Display the function name. # (DEH-2300UB, DEH-2300UBB and DEH2320UB) Press S (SRC/OFF) and hold until function name appears in the display. En # (DEH-2310UB) Press M.C. and hold until function name appears in the display. 3 Turn M.C. to select the initial setting. After selecting, perform the following procedures to set the initial setting. CLOCK SET (setting the clock) Only for DEH-2310UB. 1 Press M.C. to display the setting mode. 2 Press M.C. to select the segment of the clock display you wish to set. Hour—Minute 3 Turn M.C. to adjust the clock. CLOCK (clock display) Only for DEH-2310UB. You can turn the clock display on or off. The clock display disappears temporarily when you perform other operations, but the clock display appears again after 25 seconds. 1 Press M.C. to turn the clock display on or off. FM STEP (FM tuning step) Normally, the FM tuning step employed by seek tuning is 50 kHz. When AF or TA is on, the tuning step automatically changes to 100 kHz. It may be preferable to set the tuning step to 50 kHz when AF is on. ! The tuning step remains at 50 kHz during manual tuning. 1 Press M.C. to display the setting mode. 2 Turn M.C. to select the FM tuning step. 50 KHZ (50 kHz)—100 KHZ (100 kHz) 3 Press M.C. to confirm the selection. AUTO-PI (auto PI seek) The unit can automatically search for a different station with the same programming, even during preset recall. 1 Press M.C. to turn Auto PI seek on or off. AUX (auxiliary input) Activate this setting when using an auxiliary device connected to this unit. 1 Press M.C. to turn AUX on or off. USB (plug and play) Section Operating this unit This setting allows you to switch your source to USB automatically. 1 Press M.C. to turn the plug and play function on or off. ON – When USB storage device is connected, depending on the type of device, the source is automatically switched to USB when you turn on the engine. If you disconnect your USB storage device, this unit’s source is turned off. OFF – When USB storage device is connected, the source is not switched to USB automatically. Please change the source to USB manually. ILLUMI (illumination color select) Only for DEH-2310UB. 1 Press M.C. to display the setting mode. 2 Turn M.C. to select the desired setting. RED (red)—GREEN (green) 3 Press M.C. to confirm the selection. SW CONTROL (rear output and subwoofer setting) The rear speaker leads output and RCA output can be used for full-range speaker or subwoofer connection. If you switch to REAR-SP :SW, you can connect a rear speaker lead directly to a subwoofer without using an auxiliary amp. Initially, REAR-SP is set for rear full-range speaker connection (FUL). 1 Press M.C. to display the setting mode. 2 Turn M.C. to change the output and press to se lect. REAR-SP—PREOUT 3 Turn M.C. to change the setting. REAR-SP: FUL—SW PREOUT: SW—REA ! Even if you change this setting, there is no output unless you turn the subwoofer output on (refer to SUBWOOFER1 (subwoofer on/off setting) on page 9). ! If you change this setting, subwoofer output in the audio menu will return to the factory settings. DEMO (demo display setting) 1 Press M.C. to turn the demo display on or off. SCROLL (scroll mode setting) When ever scroll is set to ON, recorded text information scrolls continuously in the display. Set to OFF if you prefer the information to scroll just once. 1 Press M.C. to turn the ever scroll on or off. TITLE (multi-language) This unit can display the text information of a compressed audio file even if they are embedded in a Western European or Russian language. ! If the embedded language and the selected lan guage setting are not the same, text information may not be displayed properly. ! Some characters may not be displayed properly. 1 Press M.C. to display the setting mode. 2 Turn M.C. to select the desired setting. EUROPEAN (European)—RUSSIAN (Russian) 3 Press M.C. to confirm the selection. PW SAVE (power saving) Only for DEH-2300UB, DEH-2300UBB and DEH2320UB. Switching this function on enables you to reduce the consumption of battery power. ! Turning on the source is the only operation al lowed when this function is on. 1 Press M.C. to turn the power save on or off. Using an AUX source 1 Insert the stereo mini plug into the AUX input jack. 2 Press S (SRC/OFF) to select AUX as the source. Note AUX cannot be selected unless the auxiliary setting is turned on. For more details, refer to AUX (auxiliary input) on the previous page. Sound mutin...

Download now

Please, enter two numbers from picture: