Manafacture: Pioneer File size: 3.21 mb File name: Language of manual:

Photos and specs  Pioneer  DEH-1410UB

Free link for this manual available at the bottom of the page

After selecting, perform the following procedures to set the audio function. FAD/BAL (fader/balance adjustment) 1 Press M.C. to display the setting mode. 2 Press M.C. to cycle between fader (front/rear) and balance (left/right) . 3 Turn M.C. to adjust speaker balance. ! When the rear output and RCA output setting are SW, you cannot adjust front/rear speaker balance. Refer to REAR-SP (rear output setting) on the next page. Refer to PREOUT (preout setting) on the next page. PRESET EQ (equalizer recall) 1 Press M.C. to display the setting mode. 2 Turn M.C. to select the equalizer. DYNAMIC— VOCAL— NATURAL— CUSTOM — FLAT— POWERFUL 3 Press M.C. to confirm the selection. ! You can also switch the equalizer by pressing repeatedly. TONE CTRL (equalizer adjustment) ! Adjusted equalizer curve settings are stored in CUSTOM. 1 Press M.C. to display the setting mode. 2 Press M.C. to select BASS (bass)/ MID (mid) / TREBLE (treble) . 3 Turn M.C. to adjust the level. Adjustment range: + 6 to – 6 LOUD (loudness) Loudness compensates for deficiencies in the low- frequency and high-frequency ranges at low volume. 1 Press M.C. to select the desired setting. OFF (off) — LOW(low) — HI (high) SUB. W (subwoofer on/off setting) Function settings 1 Press M.C. to display the main menu. Operating this unit This unit is equipped with a subwoofer output which can be turned on or off. 1 Press M.C. to select the desired setting. NOR (normal phase) — REV (reverse phase) — OFF (subwoofer off) SUB. W CTRL (subwoofer adjustment) The cut-off frequency and output level can be ad justed when the subwoofer output is on. Only frequencies lower than those in the selected range are outputted from the subwoofer. ! When you select OFF in SUB.W, you cannot select this function. For details, refer to SUB. W (subwoofer on/off setting) on the previous page. 1 Press M.C. to display the setting mode. 2 Press M.C. to cycle between the cut-off frequency and output level of the subwoofer. Cut-off frequency (Cut-off frequency display flashes.) — Output level (Output level display flashes. ) 3 Turn M.C. to select the desired setting. Cut-off frequency: 50HZ— 63HZ— 80HZ— 100HZ— 125HZ Output level: – 24 to + 6 SLA (source level adjustment) SLA (Source level adjustment) lets you adjust the volume level of each source to prevent radical changes in volume when switching between sources. ! Settings are based on the FM volume level, which remains unchanged. ! The MW/LW volume level can also be adjusted with this function. ! When selecting FM as the source, you cannot switch to SLA. 1 Press M.C. to display the setting mode. 2 Turn M.C. to adjust the source volume. Adjustment range: + 4 to – 4 3 Press M.C. to confirm the selection. Initial settings Important PW SAVE (power saving) is cancelled if the vehicle battery is disconnected and will need to be turned back on once the battery is reconnected. When PW SAVE (power saving) is off, depending on connection methods, the unit may continue to draw power from the battery if your vehicle’s ignition doesn’t have an ACC (accessory) position. 1 Press and hold SRC/OFF until the unit turns off. 2 Press SRC/OFF and hold until function name appears in the display. 3 Turn M.C. to select the initial setting. After selecting, perform the following procedures to set the initial setting. CLOCK SET (setting the clock) 1 Press M.C. to display the setting mode. 2 Press M.C. to select the segment of the clock display you wish to set. Hour— Minute 3 Turn M.C. to adjust the clock. CLOCK (clock display) You can turn the clock display on or off. The clock display disappears temporarily when you perform other operations, but the clock display appears again after 25 seconds. 1 Press M.C. to turn the clock display on or off. FM STEP (FM tuning step) Section Operating this unit Normally, the FM tuning step employed by seek tuning is 50 kHz. When AF or TA is on, the tuning step automatically changes to 100 kHz. It may be preferable to set the tuning step to 50 kHz when AF is on. ! The tuning step remains at 50 kHz during man ual tuning. 1 Press M.C. to select the FM tuning step. 50 (50 kHz) — 100 (100 kHz) AUTO-PI (auto PI seek) The unit can automatically search for a different station with the same programming, even during preset recall. 1 Press M.C. to turn Auto PI seek on or off. AUX (auxiliary input) Activate this setting when using an auxiliary device connected to this unit. 1 Press M.C. to turn AUX on or off. USB PNP (plug and play) This setting allows you to switch your source to USB automatically. 1 Press M.C. to turn the plug and play function on or off. ON – When USB storage device is connected, depending on the type of device, the source is automatically switched to USB when you turn on the engine. If you disconnect your USB storage device, this unit’s source is turned off. OFF – When USB storage device is connected, the source is not switched to USB automatically. Please change the source to USB manually. REAR-SP (rear output setting) The...

Other models in this manual:
Car Receivers - DEH-1420UB (3.21 mb)
Car Receivers - DEH-1400UBB (3.21 mb)
Car Receivers - DEH-1400UB (3.21 mb)

Download now

Please, enter two numbers from picture: