Votes - 3, Average rating: 4.7 ( )

Manafacture: iSimple File size: 668.88 kb File name: Language of manual:

Then access SAT mode again to begin normal gateway operation. 8. Sirius Satellite radio Operation Entering Mode Select Menu Press the “AM-FM” button then press the “XM or “AUX” button. Turn the rotary TUNE KNOB or press “TUNE ^” until “SIRIUS” is displayed. The PXAMG will auto select the mode after 6 seconds of inactivity. Channel Up Turn the rotary TUNE KNOB clockwise or press the “TUNE ^” button to move up through the channels Channel Down Turn the rotary TUNE KNOB counter-clockwise or press the “TUNE Ў” buttonto move down through the channels Category Selection Non-Navigation Radios Press the “FOLDER ^” or “FOLDER Ў” button to move through the categories Navigation Radios Press the “ENTER” button to bring up the categories menu. Turn the ROTARY KNOBuntil the category you wish to select is highlighted. Press the “ENTER” button to select the displayed category. Store Presets Press and hold the preset button (1-6) for 2 seconds where you wish to store the preset. An audible beep will be heard when station has been stored sucessfully. Recall Presets Press the preset button (1-6) for the preset you wish to recall. Changing Display Press the “DISP” button to display artist and track information 9. Selecting AUX Input Entering Mode Select Menu Press the “AM-FM” button then press the “XM or “AUX” button. Turn the rotary TUNE KNOB or press “TUNE ^” until “AUX” is displayed. The PXAMG will auto select the mode after 6 seconds of inactivity. 5 10. Troubleshooting Symptom Cause Remedy I don’t see artist or song informationon the screen The radio is displaying a different text field Press the Text / Scan button to see text The Media Gateway doesnot recognize theSatellite Radio tuner (SCC1) The Satellite tuner was not properlyconnected when the PXAMG was first connected and initialized. SCC1 must be connected before the PXAMG is powered on. Disconnect the PXAMG from the vehicles harness for 5 minutes. Verify the 8 pin DIN SCC1 cable is securely connectedat both ends before reconnecting thevehicle harness. Radio shows “DEV INIT” Gateway device isinitializing This only occurs the first time thePXAMG is powered on. Wait a few minutes, cycle ignition off and on then enter SAT Mode. 11 11. Warranty One Year Limited Warranty The quality controls used in the manufacture of this product will ensure your satisfaction. This warranty applies only to the original purchaser of this product from an authorized iSimple® dealer. This warranty covers any supplied or manufactured parts of this product that, upon inspection by iSimple® authorized personnel, is found to have failed innormal use due to defects in material or workmanship. This warranty does not apply toinstallation expenses. Attempting to service or modify this unit, operating this unit underconditions other than the recommended voltage will render this WARRANTY VOID. Unless otherwise prescribed by law, iSimple® shall not be liable for any personal injury, property damage and or any incidental or consequential damages of any kind (including water damage) resulting from malfunctions, defects, misuse, improper installation or alteration of this product. All parts of this iSimple® product are guaranteed for a period of 1 year as follows: Within the first 12 months from date of purchase, subject to the conditions above, iSimple® will repair or replace the product at their discretion, if it is defective in material or workmanship providing it is returned to an Authorized iSimple® dealer, with PROOF OF PURCHASE from an authorized iSimple® dealer. Warning: This equipment may be reset by unintentional electrostatic discharge during operation. Exposure to direct sunlight or extreme heat may cause damage or malfunction. FCC Class B Radio Frequency Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: 1. Re-orientate or relocate the receiving antenna. 2. Increase the separation between the equipment and receiver. 3. Connect the equipment into an outlet on a circuit different from that of which the receiver is connected. 4. Consult the dealer or an experienced radio / television technical for help. Notice : The changes or modifications not expressly approved by the party responsible for compliance could void the user authority to operate the equip...

Download now

Please, enter two numbers from picture: