Votes - 2, Average rating: 3.5
(
)
)
|
manual abstract
The manufacturer is not liable to damage caused by improper handling or by disregarding the safety precautions. Take care that empty remote control batteries are not put into the household waste but disposed off properly (return to specialist stores, special waste) > 80% <+ 15° C Styrofoam packing harmful to the environment has not been used. The packing which can be recycled corresponds to the requirements of the new packing regulations. Never open the device. There is danger of an electric shock. Repairs should only be carried out by qualified specialists. Operational breaks: during a storm or when operation is interrupted for a long time disconnect the device from mains. In the following cases disconnect the device from mains and ask a specialist for help: - the power supply cord or the connector are damaged - the device was exposed to humidity or a liquid has flown into the device - in case of considerable malfunctions - in case of considerable external damage. MADE IN GERMANY ANT TV LNBDC 13/18VMAX 0,4A) KANAL 230-240V50 Hzmax. 24 V + 35° C 230V 5 3 Connections 3.1Outdoor unit If possible, try to use an outdoor unit TWIN LNB to be able to receive satellite TV channels and digital channels at the same time, independent of each other. If you do not want to receive TV and digital radio channels at the same time, you may continue to use your V/H LNB (s. 3.3 Satellite TV receivers). Connect the LNB input of the ASTRASTAR AX 1 with the LNB of your receiving equipment using an adequate If the LNB input is overloaded the message “cable error” appears in the display after switching on. If there is a short-circuit on the LNB input, the ADR receiver switches off (a “ticking” is heard). In both cases switch off the ASTRASTAR AX 1 using the mains switch and eliminate the error cause. Observe also 4 “Installation”. ADR ST 3004 S HiFi Outdoor unit: TWIN-LNB You can also connect the ASTRASTAR AX 1 to an ISISAT serial distribution. Please take into consideration that in this case not all channels can be received. ADR 2-way distributor external voltage supply HiFi Outdoor unit: ISISAT A/B or ISISAT A/B/C for a single cable solution ST 3004 S 3.2HiFi amplifier Connect the audio analogue outputs of the ADR receiver ASTRASTAR AX 1 with an adequate amplifier input of your HiFi equipment (e.g. CD or AUX). Caution, the phono input is not adequate! Devices with digital inputs (amplifiers, DAT recorders etc.) you can connect to the electrical digital output. Corresponding connection cables you can buy from your TechniSat sales representative. 3.3Satellite television receiver If you want to operate your ADR receiver and a satellite television receiver with a V/H LNB connect the coax cable from the LNB input of the satellite television receiver to the TV receiver connection of the ADR receiver. 6 ADR ST 3004 S HiFi Outdoor unit: V/H-LNB In this case you cannot receive TV channels and digital radio channels at the same time. As soon as the ADR receiver is disconnected from the network or the ADR receiver is in standby mode the LNB voltage is switched through to the LNB by the satellite television receiver. Moreover, you can connect the audio outputs of your satellite television receiver to the audio analogue inputs of your ADR receiver. The audio signals of the satellite television receiver are transmitted to the amplifier when the ADR receiver is disconnected from the network or is in standby mode. 3.4Personal computer You can connect a personal computer to the female connector PC IN/OUT that can be used to control the ADR receiver. The software and connection cables you can buy from your TechniSat sales representative. 4 Installation 4.1Calling the installation menu The installation menu includes basic settings for the set-up of the ADR receiver. It can only be called with of a multiple key operation so that none of the settings modified by mistake. > switch off the ASTRASTAR AX 1 with > press on the ADR receiver and > at the same time switch on the receiver again with The individual settings are marked in the channel number display with the stages E1 to E7. The function which is to be modified is indicated via the information display. E1 setting the remote control code E2 selecting the display language E3 adapting the local oscillator frequency E4 selecting the search mode for Astra or other satellites E5 selecting the search range E6 deleting the channel memory E7 copying the preprogrammation The individual settings E1, E4 and E5 only serve for service purposes or are provided for future applications. A modification becomes effective when switching to the next stage. 7 4.2LOF adjustment To adapt the ADR receiver to older outdoor can modify the factory-adjusted LOF of Small frequency failures which may occur are compensated by the automatic fine tuning (AFC) of the ASTRASTAR AX 1. > call the installation menu ( > call setting E3 “LOF 9750” with or > switch to “LOF 10000” or “ISI_AB” or “ISI_ABC” or > call the installation menu ...