Votes - 3, Average rating: 4.3
(
)
)
|
manual abstract
2 Press A or V (for less than 0,5 seconds) to adjust the sound quality. To change the level rapidly, press and hold A or 7 down longer. A side V side Ifrft Increases the Decreases the v uf_ volume level. volume level. Increases the bass Decreases the bass %H5 level. level. Increases the treble Decreases the treble ~l?~ I level. level. Decreases the level Decreases the level WI of the left of the right L speaker(s). speaker(s). Decreases the level Decreases the level ~~~ of the front of the rear speakers. speakers. Note *Without selecting any mode with MODE, only the volume level can be adjusted by pressing A or T. LOUD (loudness) function Press LOUD to reinforce bass and treble especially when listening at low volume level. To cancel the loudness, press LOUD again. To set the turn-on volume level The unit can be set to always turn on at the same volume level. After adjusting the volume with A or Y, press and hold POWER down for more than 2 seconds until a beep tone is heard. ~ RADIO OPERATION 1 Press any button (except ~) to turn on the unit. The radio frequency is displayed. If the unit is in the CD operation, press R/CD to select the radio operation. Press BAND to select the desired band from FM1, FM2, FM3, and AM. The band indicator [FM1, FM2, FM3, or AM] is displayed. 3 Press -TUNE+ repeatedly to tune in the desired station. Press + to increase and -to decrease the frequency. To change the frequency rapidly, press and hold + or down longer. . Adjust the volume with A or 7. m m d = m Y’ Note l FM1, FM2, and FM3 have the same frequency range. *ST indicator lights up when an FM stereo broadcast is received with a sufficient signal strength. Seek Tuning The seek function is used to search for the station automatically. 1 Press BAND toselect thedesired band. 2 Press 144 SEEK~ tostart theseek function. Press W tosearch forthehigher frequencies and M forthe lower frequencies. The seeking stops when the nearest station with good reception is tuned in. Press WI or 144 repeatedly until thedesired station lsrecewed. To turn off the radio Press R/CD or insert a disc. The radio is turned off and the CD operation starts. ~ PRESETTING STATIONS Up to 6 stations for each band [FM1, FM2, FM3, and AM] can be stored on the preset station buttons. 1 Press BAND to select the desired band from FM1, FM2, FM3, and AM. z Tune in the station to be preset. a Press one of the preset station buttons (1 -6) for more than 2 seconds until a beep tone is heard. The number of the pressed preset station button is displayed. m w J4 Repeat steps 2 and 3 to preset other stations. [ Note l As FM1, FM2, and FM3 have the same frequency range, up to 18 stations can be preset for FM. . When a station is preset on the preset station button on which another station of the same band has already been preset, the previously preset station is automatically erased. 10[ Automatic Presetting The automatic presetting function is used to automatically preset up to 6 stations for each band. 1 Press BAND to select the desired band. 2 Press and hold A.M down for more than 2 seconds until a beep tone is heard. The scanning starts from the currently displayed frequency to higher frequencies and stops when 6 stations have been preset or the receivable frequencies have been scanned once. Note l The presetting is not performed if there is no station to be tuned in. l When the automatic presetting is performed, the previously preset stations are automatically erased. =To stop the automatic presetting, press A.M again or press any of the preset station buttons (1 – 6). To scan the preset stations Press A.M for less than 1 second. Each preset station is tuned in for 5 seconds in order. To stop the scanning, press A.M again or any of the preset station buttons (1 – 6). To tune in the preset stations Press BAND to select the desired band and press the desired preset station button (1 – 6). The number of the preset station button is displayed and the preset station is received. Ill ~ CD PLAYBACK Press any button (except ~) to turn on the unit 1 Insert a disc with the labeled side uo to start playback. If adiscis already inserted, press R/CD toselectthe CD operation. DISC indicator lights up, and the track number and elapsed playing time are displayed. If a 3-inch (8 cm) CD is inserted, both CD and CD-S indicators light up. z Adjust the volume with A or V. Press these buttons to operate CD playback. Press To A Load or eject a disc. EIl Pause play. The track number and elapsed playing time flash on and off. To resume play, press ~11 again. E Forward on the disc. Press and hold * down until the stari of the desired passage, then release it. 4 Reverse on the disc. Press and hold + down until the start of the desired passage, then release it. w I Skip to the next track with a short press (for less than 0.5 seconds). Each extra press skips forward one extra track. To skip forward rapidly, press and hold WI down until the desired track number is disulaved, then release it. w Re...