Votes - 2, Average rating: 4
(
)
)
|
manual abstract
7 Espanol....................................................12 Introduction Thank you for purchasing the DX-S1000 Car Audio Speakers. Although Dynex has attempted to make sure all of the information contained within this manual is accurate, please be aware that any part of it is subject to change without notice. Important safety instructions This symbol alerts the user to the presence of important instructions. Failure to heed these instructions can result in injury or damage to the speakers. If you feel unsure about installing this system yourself, have it installed by a qualified audio technician. Before installation, disconnect the battery negative (-) terminal to prevent damage to the speakers, fire and/or possible injury. Setting up the car audio speakers The following are basic installation instructions. If you feel unsure about personally installing this speaker system, Dynex recommends using the services of a professional car audio installation center. Mounting the car audio speakers 3 Mounting the car audio speakers 3 Before installation, follow these guidelines: 1 Carefully read and understand the instructions before installing this product. 2 Disconnect the negative terminal from the battery before installing this product. 3 If additional wiring is needed, we recommend running all wires prior to mounting your speaker in place. 4 Use the highest quality connectors for a reliable installation and to minimize signal or power loss. 5 Use caution before you drill or cut. Be careful not to cut or drill into gas tanks, fuel lines, brake or hydraulic lines, vacuum lines or electrical wiring when working on any vehicle. 6 Never run speaker wires underneath your vehicle. Running speaker wires inside the vehicle provides the best protection from exhaust heat and environmental elements. 7 Avoid running wires over, near, or through sharp edged surfaces. Use rubber grommets to protect any wires routed through metal, especially the firewall. 8 When running the speaker cable from the amplifier, avoid running it near sources of high current (i.e. wiring harnesses, battery cables). Mounting the car audio speakers Standard rear deck installation Grille Mountingring Speaker Mountinghole cut-out Standard door installation Grille Mounting ring Speaker Mounting hole cut-out To mount the car audio speakers: 1 Determine where the speakers will be mounted. Make sure the area is large enough for the speaker to mount evenly and deep enough for the speaker to fit. 2 Refer to the specification chart on the following page to determine the proper diameter hole to cut for your speaker model. 3 If supplied, use the plastic mounting ring as a template to mark the locations for the mounting screws. 4 Drill the holes with a 1/8" bit. 5 Be sure to observe proper polarity when connecting the wires. The speaker's positive terminal is indicated with a "+". 4 Legal notice 4 Legal notice 6 Fit the ring and speaker to the cutout. Mount them using the enclosed screws. If supplied, fit the grille inside the ring and press gently, but firmly, into place. Cut-out diameter Top-mounting depth Bottom-mounting depth Mounting height Tweeter protrusion The diagram featured above is to be used in conjunction with the specifications guide below: Specification Measurement Mounting height 7/16 Top-mounting depth 2 . Tweeter protrusion . Bottom-mounting depth 2 11/16 Cut-out diameter 5 . Sensitivity (dB) 86 Frequency response 80-20 K Recommended power (watts RMS) 60 Peak power handling (watts IPP) 120 Grille (yes or no) Yes Legal notice Copyright © 2006 Dynex. DYNEX and the DYNEX logo are trademarks of Best Buy Enterprise Services, Inc. Other brands and product names are trademarks or registered trademarks of their respective holders. Specifications and features are subject to change without notice or obligation. For service and support call (800) 305-2204. Warranty 5 Warranty 5 Warranty 90 Day Limited Warranty Dynex Products (“Dynex”) warrants to you, the original purchaser of this new car audio speakers (“Product”), that the Product shall be free of defects in the original manufacture of the material or workmanship for a period of 90 days from the date of your purchase of the Product (“Warranty Period”). This Product must be purchased from an authorized dealer of Dynex brand products and packaged with this warranty statement. This warranty does not cover refurbished Product. If you notify Dynex during the Warranty Period of a defect covered by this warranty that requires service, terms of this warranty apply. HOW LONG DOES THE COVERAGE LAST? The Warranty Period lasts for 90 days from the date you purchased the Product. The purchase date is printed on the receipt you received with the product. WHAT DOES THIS WARRANTY COVER? During the Warranty Period, if the original manufacture of the material or workmanship of the Product is determined to be defective by an authorized Dynex repair center or store personnel, Dynex will (at its sole option): (1) repair...