Votes - 2, Average rating: 3.5
(
)
)
|
manual abstract
Turn on the various components and slowly advance the volume. Remember to check and re-check all connections to insure proper installation and use. • Do not continuously use the speaker system beyond the nominal power handling capacity. • Keep recorded tapes, watches, and personal credit cards using magnetic coding away from the speaker system to protect them from damage caused by the magnets in the speakers. • If you cannot find the appropriate mounting location, consult your car dealer or your nearest dealer before mounting. • CAUTION: Take extreme caution when working near the gas tank, gas lines, brake or hydraulic lines and electrical wiring. Mounting the speakers Installation kits are available from your dealer or local stereo shop to help make your installation easy. These kits also give your installation a clean, custom appearance. Questions about installations methods please consult a professional auto sound dealer/installer for assistance. • Choose the place of installation for acoustic system. For most acoustic system stipulated regular places in the automobile approach. In this case you need to know only assembly depth. Before installation acoustic system check up their assembly depth. • At a choice of a non-standard arrangement of speakers at which it is necessary to cut them in panels of the automobile, use a mould (not included). For achievement of ideal arrangement of acoustic system keep up geometry of a mould, as it is very important for correct installation of your system (A=B=116 mm, 0C=5 mm). 3 • If it will be necessary to cut steel, reinstall the cosmetic panel in place and use the hole you have previously cut as a template. This will help to insure proper cutting and a good fit. Now, mark the locations for the speakers mounting screws, remove the panel and drill the screw holes. When finished you may replace the panel. • After cutting and drilling all holes, inspect the mounting areas for any metal burrs or rough edges. File any area that may interfere with the mounting of the speaker. • Clean any metal shavings from the mounting area and check for areas in which water may enter the speaker cavity. Treat the area for water protection when necessary. Securing the speakers • Position the speaker into the mounting hole and re-confirm the correct mounting location and hole placement. • Screw clips are provided to ensure a snug fit. These should be placed over the metal surface and line up the hole you have previously drilled with the screw clip. Place the speaker into the hole, align the holes and proceed to insert the screws. Be sure to tighten the screws evenly so that it will not warp the speaker frame. • Turn your system back on and confirm the speakers operation first at a low volume and then you may increase the volume as you desire. • After installation acoustic system and having tested it the speaker grill will have to be inserted. Turn on you system and follow these steps carefully: - locate the speaker grill; - now carefully inspect the place where the speaker grill will be mounted - there should be no blowholes; - fix the speaker grill by screws. 4 If unit fails to operate properly Carefully read the instruction to make sure the unit is being operated properly. Check the following before you take your unit to the local dealer for repair. Symptom Possible cause Solution No sound The volume control regulator set in the minimal position Adjust sound level Bad power connections Check to see that all the power and speaker leads are securely connected The audio cassette receiver is damaged Take your unit to the local dealer for repair Unnatural sound Acoustic system cables are connected without observance of polarity (+ or -) Check to see that all the power and speaker leads are securely connected Damage speaker wire or speaker Replace the speaker or speaker wires The audio cassette receiver is damaged Take your unit to the local dealer for repair Note: Good ground connections eliminate most electrical noise problems and require tight contact with the metal vehicle chassis. Remove plastics, paint or rust for good electrical contact. Specification Loudspeaker cone woofer: 13 cm (5") injection cone midrange: 3 cm (1.2") PEI dome Magnet main: ferrite 10 Oz magnet midrange: neodymium Peak output power 120 W Rated output power 60 W Impedance 4 Ohm Sensitivity 91 dB Frequency response 60-20000 Hz Dimensions 168 x 73 mm Net / Gross weight 0.73 kg / 1.66 kg Gift box dimension (L x H x W) 193 mm x 105 mm x 337 mm 5 Описание В состав комплекта входит: акустическая система защитные металлические решетки - 2 шт. провод - 2 м винт - 8 шт. хомут - 8 шт. Меры безопасности • В руководстве указаны важные указания по эксплуатации и уходу. Сохраните руководство по эксплуатации для последующего использования. • Не устанавливайте динамики на неровной поверхности, а также в местах, подверженных воздействию влажности, высокой температуры, пыли и сил...