Votes - 3, Average rating: 3.3 ( )

Manafacture: ARC Audio File size: 706.08 kb File name: XDi_comp.pdf Language of manual:

We hope you enjoy your experience with all our products and we welcome any questions or comments you may have. SPECIFICATIONS XDi 5.2 XDi 6.2 Diameter 5 .” Diameter 6 .” Musical Power 160 watts Musical Power240 watts Nor. Power 80 watts Nor. Power 120 watts Sensitivity 86dB Sensitivity 98dB Frequency response 65hzFrequency response 55hz20Khz 20Khz IMP. 4 Ohm IMP. 4 Ohm Cut Out Diameter 4 5/8” Cut Out Diameter 5 5/8” Mounting Depth 2” Mounting Depth 2 .” A WORD ON DISTORTION Most speaker damage occurs as a result of amplifier distortion also known as “Clipping”. Clipping occurs when an amp is driven beyond its maximum rated output. This kind of distortion can be hard to hear unless you know what to listen for. Any time you hear a harsh ear piercing sound at hi volume your amp is probably clipping. INSTALLATION MANUAL 1 Please check the suitability of the installation location before you begin. Do not cut any of the car’s structure. Pay attention to the mechanism of the window and door. If you do not have experience with automotive electrical and mechanical systems contact a professional installer. Paying a qualified installer is almost always cheaper then paying a dealership to repair your car. After you have found the best location for the woofer, make or enlarge the mounting hole. Make sure the opening is just large enough for the woofer to fit tightly with no gaps. Make sure the surface is flat and that the speaker does not bind up in the opening. Use an awl or felt pen to mark the panel and drill the screw holes without the speaker in place. This will save the costly mistake of punching a hole in one of your new speakers. Install the woofer with the grill ring using the 4 screws provided with this system. Firmly seat the grill into its ring. Remove the grill from the trim ring first then follow the steps below installation. 1. Place the speaker in the opening with the trim ring over it. 2. Screw the trim ring through the panel with the clips beneath. 3. Install the grill into the trim ring. Add a few drops of glue if necessary. 4. Snap in the finish ring. CAUTION: THE INSTALL 2 3 GRILL SCREWS SPEAKER GRILL RING PANEL CLIPS Install the Tweeter The tweeter comes with 2 different types of mounts. Flush mount and Surface mount. Flush Mount Cut a hole in the panel you wish to install in. Assemble the tweeter in the mount. Make sure the hole is large enough for the tweeter and install it through the hole. Firmly install the retainer to the back of the tweeter. Reinstall the panel and point the tweeter at a location between the driver and passenger at ear level. Surface Mount Hold the back piece for the mount in place and mark the screw locations. Pre drill the screw holes and the hole for the wire. Screw the mount to the panel tightly. Run the wire through the hole and gently pull it until the tweeter is fully seated in the mount. Install the retainer and point the tweeter. Crossovers Install the Crossover in a dry location and secure it firmly. Don’t just drop it in the bottom of the door. 4 Wiring When wiring this system it is important to make all connections carefully and securely. Follow the instructions carefully. All audio connections have a + and -. If one is wired backward the system will play but will sound strange. One speaker will play Out of Phase (backwards) from the others. You may notice a loss of bass response and the vocals will not be in the center of the sound field. Connect the Woofer Using the wire provided with the system connect the positive and negative to the woofer. Run these wires to the crossover and connect them to the terminals marked Woofer + and -. Connect the Tweeter Connect the positive and negative to the amplifier output. Run these wires to the crossover and connect them to the terminals marked Tweeter +and-. Connect the Amp Connect the positive and negative to the amplifier output. Run these wires to the crossover and connect them to the terminals marked Input +and-. 5 A Few Do’s and Don’ts • Always use the crossovers. To leave the crossover out will result in almost certain damage to the component speakers. • Care must be taken not to mix the tweeter and woofer connections. The system will not work and may be damaged. • Do not add more speakers to the crossover. The crossover is designed for the speakers provided only. If you have any Question about this product please call ARC Audio Technical Service: 209-543-8706 ARC AUDIO WARRANTY AND SERVICE GUIDELINES Note to International Customers- For warranty and repair service outside of the USA, please sen...

Download now

Please, enter two numbers from picture: