Votes - 1, Average rating: 5 ( )

Manafacture: Audiovox File size: 625.36 kb File name: Language of manual:

Reach through opening to access antenna lead and plug into radio. 5. Pre-test radio. 6. Slide radio into housing until locked in place. FIG. A FIBERGLASS CAP ROOF ( CROSS SECTION OF ROOF) RBERGLASSROOF CAP STEEL ROOF :":,.:;:c;:;:;c:;,,;;.:c:.:'ii:::i FIG. A DISASSEMBLY: AIR GAP 1. Remove molded inside headliner prior to installation AIR GAP 2. Do not remove the fiberglass roof cap See F1g. 1. for Installation LMOLDED HEADLINER FIG. B STEEL ROOF WITH HEADLINER {CROSS SECTION OF ROOF) FIG. B DISASSEMBLY: 1. Remove molded inside headliner prior to installation Note: If the air gap (space) between the steel roof and the headliner is less than 1/4" , refer to Fig. C See Fig. 2 for Installation FIG. C STEEL ROOF ONLY (CROSS SECTION OF ROOF) r; STEEL ROOF FIG. B DISASSEMBLY: 1. If the roof has an inside headliner that is either flush or has an air gap of less than 1/4" , do not remove the headliner L NOTE: SOME OF THESE TYPES See FIg. 3 for Installation OF ROOFS HAVE A HEADLINER THAT IS GLUED TO INSIDE OF THESE OF THE ROOF (NO GAP IS IN RG. C) FIG. 1. INSTALLATION , (INSERT AFTER ""' INSTALLATION IS WRENCH(INCLUDED) -COMPLETED) USE I SEALANT TO INSURE ~ / A LEAK-FREE SEAL / ~ ~ / STEEL CUP WASHERS I MOUNTING BOLT (SELECT LENGTH """" NEEDE FROM CHOICE OF LENGTHS ,..,.. INCLUDED) I DRILL 5/16. /r~MMEIS DIA. HOLES PER ~ - TEMPLATE -;----- APPLY A BEAD OF SEALANT AROUND / BOTH SIDES / - OF HOLES ~ FLAT WASHERS ~..-JAM NUTS (TIGHTEN ARMLY) ~ STEEL PLATE ~~ I ~ USE THESE HOLES FOR CASE 580K / ./ USE THESE HOLES / ~ FOR ALL OTHER EQUIPMENT ~ ~.J BLACK WASHERS --( 6 PCS.) , , , ~ ~ , , #6 BLACK SCREWS TRIMPLATE (6 PCS.) ~==-PLASTIC HOUSING ~0 0..,.. RADIO SHAFT NUTS ~ ~~ FIG. 3 INSTALLATION WRENCH (INCLUDED) ~ MOUNTING BOLT (SELECT LENGTH NEEDE FROM CHOICE OF LENGTHS INCLUDED) ' I G / STEEL CUP WASHERS RUBBER GROMMETS DRILL 5/16" DIA. HOLES TEMPLATE PER ~ I ~ APPLY A BEAD OF SEALANT AROUND BOTH SIDES OF HOLES ,,) ~ ~ ~..- - FLAT WASHERS JAM NUTS (TIGHTEN RRMLY) STEEL PLATE ~ ~~ USE THESE HOLES FOR CASE 580K ~ USE THESE HOLES / FOR ALL OTHER EQUIPMENT ~ ~ ~ J ~ ~c --:-:"" ---: ~ ~ ~~ BLACK WASHERS (6 PCS.) #6 BLACK SCREWS TRIMPLATE (6 PCS.) PLASTIC HOUSING 0 0~ RADIO SHAFT NUTS ~ Cab Wiring I. Route pre-installed antenna lead to mounting plate for connection to radio later in installation. 2. Locate the two wire (Red and Black) harness and the single Green/White stripe harness in this kit. 3. Connect the Black wire to vehicle ground using the crimp-on ring terminal and screw included. 4. Splice the Red wire to any + 12 volt accessory wire in the cab using the quick splice included. 5. Splice the Green /White stripe wire to any + 12 volt battery source in the cab using the quick splice connector included. 6. Route all three wires to the radio mounting plate for later connection. ( FIG. 5 CAB WIRNG CRIMP-ON RING TERMINAL RED TD + 12 VOLT ACC. QUICK SPLICE ~ CONNECTOR /" ~ BLACK ~ GREEN/WHITE WIRE "' TO VEHICLE ,," TO +'12 VOLT BATTER~ ~ GROUND (ONLY ON CE1 00/200...

Download now

Please, enter two numbers from picture: