Capitalizing on athena’s breakthrough research and development in acoustics and speaker engineering, this system is designed inside out to work together perfectly, with such features as timbre- matched drivers and Medium Density Fiberboard (MDF) cabinets to minimize resonance and enrich the deep bass.The POINT5 MK II system comes complete with four S.5 satellite speakers, and the matching C.5 center channel. For bass enhancement, add the matching active subwoofers AS-P300 or AS-P400. Both subwoo

Finally, LEFT and RIGHT modules have the same module address. For example, speakers 1-8 both “L” & “R” modules would have the following module address: Tens= 0; Units= 0; Group= 4. For speakers 9-16, both “L” & “R” modules would have the following address: Tens= 0; Units= 1; Group= 4, etc...) 2048 Mercer Road, Lexington, Kentucky 40511-1071 Phone: 859/233-4599 • Fax: 859/233-4510 Customer Toll-Free USA & Canada: 800/322-8346 Website: Technical Assistance: Mon-Fri 8:30 AM to 5:00 PM Eastern Tim

9) Insert the speaker bezel into the hole, and using a Philips screwdriver, tighten the screws attached to the dog clamps until firm. DO NOT OVERTIGHTEN 10) Once the bezel is installed, install the speaker into the mounting bezel and using a Philips screwdriver, tighten the screws until firm. DO NOT OVERTIGHTEN PAINTING THE BEZEL AND GRILLE If you wish, you can paint the speaker bezel and grille to match the decor and design of your home. 1) For the in wall model, simply separate the bezel from

The most popular places used for surround speaker placement are the following: Side walls: To maximize the ambient field for side wall mounting, position the speakers adjacent to and slightly behind the primary listening area at a height of approximately 6 feet. Rear walls: To maximize the ambient field for rear wall mounting, position the speakers so they flank the main listening area and point towards the front of the room. They should be raised to a height of approximately 6 feet and should i

Warning: If an amplifier is over-driven, the resulting distortion is actually many times greater than its rated power. Over-driven amplifier distortion is called "Clipping", easily identified by its fuzzy, distorted sound, and can damage any speaker. The volume control of most amplifiers and receivers is a logarithmic type, which means that full power may be reached with the volume control set at as little as the halfway point. Operating the loudness, treble, or bass controls increases power out

La garantie ne couvre aucun dommage subi pendant le transport ou imputable a un accident, a une utilisation impropre ou abusive, a la negligence, a une modification non autorisee, a la non-observance des instructions decrites dans le manuel de l’utilisateur ou des directives d’entretien, ni aucun dommage subi par suite de reparations non autorisees ou de reclamations fondees sur une mauvaise interpretation des conditions de la presente garantie par le revendeur. Service sous garantie Dans l’even

The speaker wire is the only contact the speaker has with the amplifier. If thin, low quality cable, such as "lamp cord" is used, then the overall sound quality will suffer, particularly in lengths of 10 feet or more. We strongly recommend the use of high quality speaker cable to obtain the best performance from your speakers. • WARRANTY OUTSIDE OF THE UNITED STATES AND CANADA Outside of North America the warranty may be changed to comply with local regulations. Ask your local athena TECHNOLOGIE

Periodically use a soft, dry cloth to remove dust or fingerprints. Do not use paper towel or other abrasive materials as it may damage the finish. NOTE: Please retain the carton and packing material for the athena TECHNOLOGIES® speakers to protect them in the event of a move or if they need to be shipped to a service center. Product received damaged by a service center that has been shipped by the end user in other than the original packaging will be repaired, refurbished and properly packaged f

Not doing so could result in potential damage to the system. Connecting the Speakers On the rear of your athena TECHNOLOGIES® speakers are red and black binding posts. Using standard speaker wire, connect the system one channel at a time, and start your process at the Receiver. Connect the speaker wire from the positive (RED +) terminal on the receiver to the positive (RED+) terminal on the speaker. Connect the negative (BLACK-) terminal on the receiver to the negative (BLACK-) terminal on the s