Votes - 1, Average rating: 5
(
)
)
|
Photos and specs Pioneer S-ES3TB |
manual abstract
Please read through these operating instructions before using your speaker system to optimize performance. • The nominal impedance of this speaker system is 8 .. Connect the speaker system to an amplifier with a load impedance ranging from 6 . to 16 . (a model with “6 . to 16 .” displayed on the speaker output terminals). • In order to prevent damage to the speaker system resulting from input overload, please observe the following precautions: -Be sure to turn the connected devices off and remove the power cord from the wall outlet beforehand when changing the connection or installation method. -Do not use excessive amplifier volume if using a tone control to emphasize high or low frequencies. • Do not use the speaker to output distorted sound for long periods of time. This can result in a fire hazard. INSTALLATION PRECAUTIONS • Do not install these units near a stove or other heating appliance, or put them in a place exposed to the sun. Such locations may cause the cabinet to change color and the speaker system to break down. FRONT / CENTER SPEAKERS • Do not attach the front and center speakers to the wall or ceiling. It may fall off and cause injury. • This speaker system is magnetically shielded. However, depending on the installation location, color distortion may occur if the speaker system is installed extremely close to the screen of a television set. If this happens, turn off the television, then turn it on again after 15 min to 30 min. If the problem persists, place the speaker system away from the television set. • Do not install your speakers overhead on the ceiling or wall. The grille is designed to be detachable, and as such it may fall and cause damage or personal injury if installed overhead. SURROUND SPEAKERS • The surround speakers are not magnetically shielded and so should not be placed near a TV or monitor, as the interaction of magnetic materials can cause distortion of the colors on your TV screen. Magnetic storage media (such as floppy discs and tape or video cassettes) should also not be kept close to these speakers. PLACEMENT AND FINE TUNING FRONT SPEAKERS For best results the speakers should be separated a distance approximately equal to the listening distance. Angling the speakers inward towards the listener will improve the image stability for non-central listeners. Close proximity to a side or rear wall will enhance the midbass performance, although too close (particularly a corner location) and the bass may be unnaturally high and image performance may be degraded. .Front speakers x 2 .Surround speakers x 2 .Speaker cords x 5 .Center speaker x 1 .Non-skid pads x 12 (4 pcs x 3 sheets) .Grilles (for front speaker) x 2 .Operating instructions Center (2 m, Tie color : Black) Front right / left (3 m, Tie color : Blue) Surround right / left (10 m, Tie color : Red) 2 En CENTER SPEAKER The speaker should be positioned below the TV. For best results align the front of the speaker with the front of the TV. If the speaker is placed under the TV and very close to the floor, then tilting upwards may be beneficial. Do not place the center speaker on top of TV, the speaker may fall from the TV due to external shocks such as earthquakes, endangering those nearby or damaging the speaker. SURROUND SPEAKERS For best results the speakers should be positioned at or above ear level. Depending upon your room layout and preferences, the left and right rear speakers should be positioned on the side walls just the rear of the listening position, or on the walls. STANDARD SURROUND SETUP This is a standard multichannel surround sound speaker setup for optimal 5.1 channel home theater sound. NON-SKID PADS If the front, center and surround speakers are placed on a hard surface, such as wood or tile place four non-skid pads on the bottom flat surface of the speakers. MAKING AMPLIFIER SETTINGS Before connecting the speakers, please read the operating instructions supplied with your amplifier to select the speaker setting of amplifier : • FRONT SPEAKERS : LARGE • CENTER / SURROUND SPEAKERS : SMALL CONNECTING YOUR SYSTEM Make sure all equipment is turned off before making any connections. • Correct wiring of your speakers is essential for achieving the best sound quality. Be careful to ensure proper polarity of connection. Connect to the speaker terminals on the rear of the amplifier. Connect the striped speaker cord to the red (+) terminal and the other cord to the black (–) terminal as shown below (for more details, refer to your amplifier instruction manual). Connect to the speaker terminals on the rear of the speakers. • For front speakers: Unscrew the terminals on the speaker and insert the striped speaker cord into the red (+) terminal and the other cord into the black (–) terminal as shown below. • For all other speakers: To connect, press the lever and insert the striped speaker cord into the red (+) terminal and the other cord into the black (–) terminal as shown below. Surround left Surround right Cen...